20 Most Recent
Mitsubishi WS-55807 TV - Page 9 Questions & Answers
Child lock
press down the key with the lock symbol for at least four seconds ,then you can see the option to lock ,unlock etc.try it.thank you
Picture bows
It's ring-cracked solder joints on the foil side of the board, most likely in the convergence circuit...
Bill
Need some info tv turns on then goes off
Good Day,
Try these:
This model is equipped with a self-diagnosis feature to help with diagnosis of shutdown problems. To activate this turn the unit on let it shutdown then press the input/device and menu buttons on the front panel simultaneously and hold them in for 5 seconds after 5 seconds the power LED on the front panel will blink a two digit sequence. This will be one set of blinks a short pause then another set of blinks, this will repeat 5 times. 1 - 2 = no error detected 2 - 1 = X-ray protect (high voltage or beam current) 2 - 2 = Short protect (short protect monitors low voltage supplies) 2 - 3 = Deflection protect (this could be loss of vertical or horizontal deflection) 2 - 4 = Vertical protect (usually loss of vertical from the source) 1. SELF- DIAGNOSIS INDICATE X-RAY. CHECK FOR A SHORTED IC5A03 PART # 270P704010 AND AN OPEN R5A73 82K ¼ WATT OFF PIN 2 OF IC5A02 ON THE MAIN PCB. 2. SELF DIAGNOSIS ERROR INDICATES SHORT PROTECT. CHECK FOR OPEN FUSES F9A04 AND F9A05 PART # 283P043090 ON THE +24 AND -24 VOLT LINES. IF THE FUSES ARE OPEN THE CONVERGENCE OUTPUT CIRCUIT WOULD BE SUSPECT. 3. SELF-DIAGNOSIS INDICATES SHORT PROTECT. CHECK FOR A SHORTED IC4B01 PART # 270P261020 (VERTICAL OUTPUT) LOADING 24-VOLT SUPPLY LINE. LOCATED ON THE MAIN PCB.
Good Luck, big IRISH.
I cant get high def 1080-i to work on my mitsubishi 55807
IYou have to have your comcast
box tuned to a channel that is broadcast in HD. On your Comcast remote
hit menu. This will bring up several icons, one is HD. Select that icon
and it will bring up the TV
Guide for just HD channels. Select one and tune to that channel. Once
your on that channel use your original remote and hit menu, then
advance features, then go down to video display and change it from 480
to 980 or 1080. Let me know if this helps.
I just subscribed to HD
IYou have to have your comcast box tuned to a channel that is broadcast in HD. On your Comcast remote hit menu. This will bring up several icons, one is HD. Select that icon and it will bring up the TV Guide for just HD channels. Select one and tune to that channel. Once your on that channel use your original remote and hit menu, then advance features, then go down to video display and change it from 480 to 980 or 1080. Let me know if this helps.
Pink screen
Rick, Check the convergence Ic's on the foil side for any hairline cracks in the solder joints and re-solder them if you find any... Other than that you may need to replace the convergence Ic's and possible some of the yoke return resistors. What you're seeing on the screen is an absence of one of the colors, blue from what you're describing and that may just be one of the amps is missing voltage due to ring cracks.
Bill
Mitsubishi CK-3526R TV
not sure what light picture has to do with problem but no there is no vertical hold control prob bad electrolytics invertical feed back circuit, need tech..
Cable box
Yes, this TV will need a converter box if you are getting off-the-air reception. It does not have a DTV tuner built in (too old) although is a high-def capable set.
Mitsubishi WS55807 Converge prob.
hello yes i can tell you where to look . take front of the set off and there's a cover with screw's holdng it on . take it off . and your convergence board in the front of the set.'GOOD LUCK"
GHOST/MULTIPLE IMAGES AND COLORS ON MITSUBISHI WS55807 PROJECTION TV
In the menu ,,under settings usally ther a convergenge option,,what it does is realine the colors,, that should do the trick,,if your tv has that ,,good luck
Mitsubishi hd1080
I can't disconnect the parent v chip now it is automatically blocking stations
TV picture curves
This is a convergence problem and is usually either bad connections at the convergence ICs or defective ICs. If you can solder, you can fix this yourself. Locate the convergence ICs (large black Ics attached to a heat sink and marked STKxxx). Resolder the pins first. If that fails to resolve the problem replace the ICs.
Keep us posted.
Dan
Tv probblem
You should be able to access all the menu features from the front of the set. Or keep in mind, you can purchase any mitusbish remote and it will do most things, Just look for format button. I may even have one if you need one. Let me know if i helped you solve your problem. Good Luck. Jay
WD-62825
Drop me a personal email with the model number and I can Pando you the service manual... But be descriptive as to what you need and for what model, I get more than 3000 requests a day and too old to try and remember what requests goes with what model and to whom... :)
Bill
William Rayburn, CET
Premium Technologies
PO Box 442
Long Beach, WA. 98631
360-642-4993
[email protected]
MGA CS-2657R/2658R
Journeygal,
Check The Following Components Off Ihvt pin 3 For Open: R558 P/N 103p338010, D 553 264p338010, L502 321c030010, R521 1.2 Ohm You'll Need A DMM For The Job And Any Cheap One From Radio Shack Will Work.
Bill
Premium Technologies
PO Box 442
Long Beach, WA. 98631
360-642-4993
[email protected]
Not finding what you are looking for?