20 Most Recent
Mitsubishi WS-55807 TV - Page 4 Questions & Answers
My TV will not turn
Sounds like a power supply issue in the tv. The regulator and a fuse are probably at fault. I had one today of the same model with the same problem. There is a small solder in fuse, a soldered in regulator ic and a capacitor that needed to be changed. A reasonable repair cost for this repair would be 155-225 us dollars depending on if in-home service is needed. This is only my best guess . Hope this helps. Good luck, Russmann.
Convergence color is not converting
Replace convergence IC (location 8c01) which is a STK-393-110. You will need to order an after market market convergence IC (STK 393-110) I have had good luck with this IC. Next, check and replace all the 3.9 ohm 2 watt resistors, that are bad. You can check them with an ohm meter or visually inspect for burns or peels. Resolder the Convergence board, as by now there are many bad grounds (broken solder connections). Be sure to resolder the jumper jacks that connect the board to the next board too.(Under this board are solder traces that adhere to the jumper connections that will snap to the next board.) These would include jumper jacks PM, VU, and PF. Good luck and thanks for asking, show all hands of support!
NO POWER NO ON
possible blown fuses or defects on power line wire up to power regulator circuit
TV won"t stay on turns
Do the self check when power light goes off.
On front of set press and hold both the menu and input buttons for 5 seconds or longer and release both buttons.
Power light will blink a error code like: 2 blinks, 2 blinks, a pause and repeat about 4 more times.
Let me know what error code you find and I will tell you what it means.
If this information told you something rate this solution as very helpful as I do this here for free.
SD TECH
My mitsubishi big screen projection tv, 1080, all
you have a bad or leaky capacitor in the power supply section...if you can dismantle the back casing look for the power supply and check if there's a bulgy capacitor mostly electrolytic type....replace w/ same value..it's best if you brought it in a tv service center
I exceeded the convergence values
Hi,
This error means X-Ray protect circuit
There are several things that can cause this.
The most
common is the convergence circuit, this circuit is responsible for
lining up all the colors on the screen, however when it shorts out it
will shut the set down exactly like yours is doing. This repair normally
runs around $400.
However this could also be caused by
the horizontal circuit, deflection board, main board, fluid leak, and
high voltage circuit to name a few. The average repair price for any of
these is $400-$700 depending on exactly what is found.
To
determine exactly what the problem is will require troubleshooting. Some
knowledge of electronics and a multimeter will be needed for this. If
you have this knowledge/tools I will be more than happy to walk you
through the troubleshooting of this set and determine what is wrong.
Also most repairs will require good soldering skills so you will need
these as well for us to repair the tv after diagnosis. If you don't have
any of this then a repairman would be your next step.
I
am sorry to bring you the bad news on this one, you definitely have an
internal failure in the set that is putting it into shut down.
Let me know,if needed further assistance.
Hope i helped you.
Thanks for using ' Fixya ' and have a nice day!!
Does this tv have a
The WS-55807 is a CRT RPTV and uses CRT "Tubes/Guns". Therefore there is no "replaceable " bulb.
My mitsubishi television ws-55807 went
If power light comes on and then goes off do the self check this set has:
when light goes off and front of set press and hold both the menu and Input (device) buttons in at same time for at least five seconds and release both buttons.
The set will (the power light) blink a two digit error code like, 2 blinks, 2 blinks, a pause and repeat the code several times.
2,2 is most common error code, let me know what error code if any you find and comment here and I will tell you what it means.
The self check is designed to narrow down where a problem is.
SD TECH
No picture but have on cable disconnectd cable
Hello
There is a system reset button on the front panel of your TV. You have to reset it. Resetting will bring all the settings to factory defaults. There is a small hole on the front panel. The reset button is behind this hole. To reset do the folloing:-
If the TV doesn't respond to either the remote control or the front panel controls or will not power off, press the SYSTEM RESET button on the front panel with a pointed item such as the point of a ball point pen or end tip of a paperclip.
The TV will turn off and the green led will flash quickly for about one minute. When the green led stops flashing, you may turn on the TV again. The changes you made while the TV was most recently on, before you used the SYSTEM RESET button may lost, however, the changes you made previously are not lost. Only those changes since
power On may be lost when the system reset button is pressed. All other settings are retained.
Ok.
Picture is bowed, concave at both the top and the
You have a convergence problem. You will looking for the board with all the RCA jacks and RF connections. There you will See large heatsinks with ICs clipped to them. If you can remove the clip or clips you should note the STK IC or ICs. They may be a STK 392XXX, STK 393XXX, or a STK 394XXX. You will have replace that particular one, along with any burned or open 2 watt resistors. The Resistors may be 2 watts at 6.8 ohms. They are usually sitting tall next to the convergence IC. And in many cases you may have a weak or bad capacitor or two that may have contributed to a failing STK. Replace these caps a swell. Thanks for asking and show a few hands of support!
I have a WS-55807 that
Hi,
The code 2-2 does indicates a short protect fault, which is usually
caused by a failure in the convergence section. This is a very common
repair in these sets. The typical repair involves replacing the
convergence ICs (integrated circuits), and testing/replacing two small
pico fuses.
The replacement ICs for your set are part number: STKxxx-xxx and are available from www.encompassparts.com
for $19.95 each (needs two). You will also need at least one (likely
two) 5 Amp pico fuses. If you wish to repair this yourself, the ICs are
located on the large heat sink on the center (Power) PC board. The fuses
are also on this board, near the center, location numbers: FXAXX and
FXAXX. You would need soldering equipment and very good soldering skills
to replace these parts.
An image of the same would be ( the below one is a generic picture ) :-
If you were to call a local shop to repair this, the labor to replace
these is roughly $250-275 (in my area) if the TV were brought in to the
shop. Please add a trip charge if repaired in the home.
The fuses must be tested with a multimeter to see if they are bad. They
are only $2.50 each, so most people without a meter just change them
both. If the repair has any problems, like a solder bridge, you may need
a meter to check them after that. A good magnifying glass helps prevent
solder bridges (for me, anyway).
Let me know,if needed further assistance.
Hope i helped you.
Thanks for using ' Fixya ' and have a nice day!!
11/18/2010 11:51:53 PM •
Mitsubishi...
•
Answered
on Nov 18, 2010
The red coler has started
if your picture looks 3d it is convergence problem.
This is a do it yourself repair if you have some skill.
I will tell you what you need and have start to finish, step by step instructions for this repair along with photos, and source for parts needed(parts cost will be under 30 dollars).
reply here if I can help.
SD TECH
10/24/2010 10:17:26 PM •
Mitsubishi...
•
Answered
on Oct 24, 2010
I have a ws-55807. power
Hi
Thanks for using FixYa. Error code 2-2 means short protect which is either
caused by bad convergence ICs and/or 2 Pico fuses (F9A05 and F9A04). You'll
need to open the back of the unit and replace the parts that have gone bad to
resolve this issue. There are repair kits available which includes
repair instructions with the parts, if you want to do it yourself, you can buy
and repair it yourself. Please
accept the solution if the issue is resolved or post a comment for further
assistance.
Thanks
Rylee
The TV will not turn on. I have verified that it
It is probably a horizontal transistor gone short circuit which controls the H.V. transformer no power for picture or the H.V. transformer gone short circuit as well or it maybe a power supply fault
It shuts off within 2 seconds of being turned on
hello sir, hi your tv has power supply problem, need to check for the voltage regulator section. this is usually a transistor mounted on a heat sink. When this is bad no power will ever come on. checl also for the high voltage output section, a bad horizontal out produces the same symptom.
MY WS-55807 TURNS ON FOR
if you unplugged it you will only get the no error code 1,2.
Plug back and turn on, when light on power goes out try it again--if power light goes out there will be a error code.
SD TECH
Attn: SD Tech I also have the power problem with
the blinking light signifies to a repair technician with capacitors or circuits are having an issue they can diagnose the problem via the amount of blinks in between pauses however it will require a technician and some specific tools and schematics to fix and it may be cheaper if its no longer under warranty to purchase a new one
Hope this helped
Robb
Not finding what you are looking for?