error sc541
sc541 is a fusing unit error code. Can you reset the code in service mode?
Posted on Apr 23, 2008
Paper tray 2 problem displaying the error code above.
sc 502 is the problem related to tray lift motor .open the backside of the machine ,almost downside u ll find one spring broken .replace tat the tray will start working.
Posted on Jan 21, 2009
Ricoh Afico 2075 sc551 error code. the thermistors and thermostats have been replaced and yet the code still pops up any ideas? Both fuser rollers have been replaced. the connectors have been ohmed out on the fuser and the frame connector.
Press total clear (yellow key) , 107 and press and hold the clear stop key (orange key) more than 3 seconds, shut off and on the copy.
Good luck.
Posted on Sep 14, 2009
HI I HAVE JUST PURCHASED A REFURBISHED AFICIO 2035 E, BUT I DO NOT KNOW HOW TO RESET THE MACHINE BACK TO ITS FACTORY/ DEFAULT SETTINGS.
ANY HELP WOULD BE GREAT
Hello sir; You have to print out SMC list before you clear all memory then to reset, the procedure as follow;
1, press "clear mode", "107".then hold down "clear/stop" key.
2 enter 5990 press enter.
3, touch on screen "execute".
after print out go backto clear memory.
4, enter 5801-1
5, follow the list to reset each item.
Posted on May 27, 2009
receiving a error code E-3) 3) 3) 3) 3). What does this mean?
Is absent Block of the Manifestation or is drived activator of the sensor, sensor burns out seldom and can be unplugged (on the right at the top on block)
Posted on Oct 03, 2009
Ricoh 2045 error code SC350
It can be dirty ID sensor it retires the image unit and it cleans it… This happens when mylar of the cleaning unit is damaged…
Posted on Dec 07, 2009
I tried sending a fax from my Ricoh MPC 4000 and in the confimation Report where it usually says ok it says E-3) 3). I can not figure out what that means...
On the report where it shows the E-3 error, it should have a legend further down the page that shows what each error means. I think E-3 is "line busy," but check that legend to be sure.
Posted on Jun 05, 2010
All service codes for ricoh aficio 1075 are required urgently.
RICOH ERROR CODES
Error Code Description
SC184 CIS Transmission Error
SC191 Bar Code Scanning Error SC192 Automated SBU Adjustment Error/Bar
Code Number is Different SC193 Image Transfer Error/IDU Error
SC194 SBU White Level Detection Error SC195 DF Gate Assert Error/Serial Number Error
Error SC196 DF Gate Negate Error
Code Description
SC197 DF Gate Error SC101 Exposure Lamp Error
SC198 Memory Address Error SC107 Scanner Lamp Regulator Malfunction
SC199 DF Scanning Finish Error SC120 Scanner Home Position Error 1
SC201: Polygon Motor Error HP Sensor Abnormal-Stays Off
SC220 Laser Synchronization Detection Error SC121 Scanner Home Position Error 2
SC221 Scan Length Detection Error HP Sensor Abnormal-Stays On
SC230 BCU Received no Feedback from LD SC122 Scanner Home Position Error 3
F- Gate Error SC123 Scanner Home position Error 4
SC231 Laser Beam Feedback Signal Error SC124 Scanner Motor Encoder Signal Error
F- Gate Timeout SC125 Scanner Motor Speed Error 1
SC240 LD Power Supply Excessive SC126 Scanner Motor Speed Error 2
SC260 HP Sensor Error SC127 Scanner Motor Encoder Rotating Direction
SC261 HP Sensor Not Turning Off Error
SC285 Line Position Error SC128 Scanner Motor Start Error
SC300 Charge Corona Output Error 1 SC129 Scanner Motor Speed Control Error
SC301 Charge Corona Output Error 2 SC130 SBU defective Error/Scanner Start
Charge Current Leak Abnormal
SC302 Charge Corona Output Error 3 SC131 F-Gate Asserted During Shading
Grid Voltage Error Charge Roller Current Leak
SC142: White level detection error. SC303 Charge Corona Output Error 4
SC143 SBU Auto Adjust Error Grid Leak
SC144 SBU Connection Error Charge Cleaner Motor Error SC150 Scanner ROM Mismatch SC304 Charge Roller Current Correction Error SC170 Scanner DA1 Abnormal/Video Processing SC305 Charge Corona Wire Cleaner Error 1
Error 1 SC306 Charge Corona Wire Cleaner Error 2
SC171 Scanner DA2 Abnormal/Video Processing Charge Roller Home Position Error Error 2
SC310 Potential Sensor Calibration Error 1 SC172 Scanner DA3 Abnormal/Video Processing
SC311 Potential Sensor Calibration Error 2 Error 3
SC312 Potential Sensor Calibration Error 3 SC173 Scanner Lamp Regulator Adjustment Error
SC314 Potential Sensor Calibration Error 4 SC174 Scanner DA2 Abnormal
SC315 Potential Sensor Calibration Error 5 SC181 CIS Lamp Abnormal
SC316 Potential Sensor Calibration Error 6 SC183 CIS Auto Adjust Error
SC317 Potential Sensor Calibration Error 7
www.smilecopy.com
Posted on Aug 13, 2010
Ricoh MP 2851 has toner depleted fault. Toner bottle was replaced and fault remains. Replaced with a 2nd Toner bottle, fault remains.
Hello!
I believe that you closed all the doors properly...
Well, this may happen because off several things.
I can give you some tips (by steps):
- First you have to make sure that the toner bottle spins (if that doenst happen it could be a faulty clutch).
- Than you need to see if the tonner supply (the green handel that you place the toner) are good.
- After that you just have the TD sensor. This sensor is on the Developement Unit.
Well, i am just giving you a clue. If you do not have thecnical knoledge i advise you to call your provider.
See you, And good luck
Posted on Jul 20, 2011
Please wait for extended time then SC 672. Have tried another HDD, reseated all connectors on control board and control panel as well as checked all other connectors. Tried reloading firmware thru sd card and didn't recognize the card. tried booting with HDD disconnected and still codes out with SC 672
Try checking or changing the thermistors!
The metal contact spring on the thermistor broken causing all sorts of 'unrelated errors including 'Please Wait' sc 670 and sc 402...
Posted on Feb 29, 2012
753 questions posted
Usually answered in minutes!
382 Questions
267 Questions
215 Questions
218 Questions
230 Questions