20 Most Recent
Ricoh Aficio 2015 Copier - Page 8 Questions & Answers
Ricoh aficio 2232c sc542 error
SC542 means that the thermistor hasn't detected right temperature in given time.
Often you only have to reset service code.
Try this reset:
- Press and hold online + escape, then power on.
- Use up and down arrow keys to select SP2
- Press Enter
- Use up and down arror to locate SP5
- Press Enter
- Use up and down arrow keys to select 810
- Press Enter
- Confirm the selection
- Power off and on.
from http://www.fortc.com/2007/06/17/ricoh-cl4000dn-error-code-sc542/
here is another service procedure:
- Press Mode(The Yellow Button)
- Enter 107
- Press STOP Button for 3 second (RED Button)
- Copy Sp
- 5810#
- Execute
- Power Off
- Power On
The toner refill with compatible powder, but the
well this is because when you replace the powder it never has the same quality this is because there are always traces of old toner and it mixes together even though it is compatible dosent mean its exactly the same never use refills its a waste of time and money these company's make me sick saying the quallity is the same most of the time they instruct you to make a hole and cover it with a stupid bit of tape and other times there is a refill hole but this is not for us to use it is for a factory so a machine can blast air into it to make sure it is clean and then refill it
if you insist on refilling again use an air gun to remove all of the toner then it will be slightly better but it will never be as good
I have a problem RICOH
SC 500 : Main motor lock
Symptom:
A main motor lock signal is not
detected for more than 7 consecutive
checks (700 ms) after the main motor
starts to rotate, or the lock signal is not
detected for more than 7 consecutive
checks during rotation after the last
signal
Possible Cause:
• Too much load on the drive
mechanism
• Main motor defective
Sc982
Press Ok, Accept or
replay
I have a solution for
this
Bruce
Sc code 550
sc 550 is main motor error. i think the main motor needs replacing
Sc 390
SC 390 TD sensor error
The TD sensor outputs less than 0.5V
or more than 4.0V 10 times
consecutively during copying.
• TD sensor abnormal
•
Poor connection of the PCU
Paper stuck
open the right door to check the paper jam - thanks
Photo copier error code on ricoh 2018 code is 322
SC 322 is as follows.
322 C 1st laser synchronization error The 1st laser synchronization signal cannot be detected by the main scan synchronization detector board even if the laser diodes are activated.
Causes
• Poor cable connection between the laser synchronization detector board and the LD unit.
• Laser synchronization detector board out of position and angle of reflection not correct
• Laser synchronization detector board defective
• LD unit defective
Basically there is something wrong with the laser unit. It is possible to take it out by removing the front of the copier between the paper tray and paper output deck. UNLESS YOU KNOW WHAT YOU ARE DOING DON'T DO IT. There is a laser in the unit that can cause instant blindness if you defeat the interlocks or repair it incorrectly. An experienced engineer would unplug the machine remove the unit, remove the top cover and clean the mirrors and glasses inside the laser unit without removing any of them, also check that the ribbon cable is correctly plugged in durin reinstallation.
I take no responsibility for these instructions or the text above, the laser unit has warnings on it that should be followed and it should only be repaired by the manufacturer in designated premesis.
Anyway hope this helps :)
Please rate.
RICOH MODEL 2015 WHAT IS
Low fuser temperature during warm up. This means that the heater lamp is not coming on or if it is the machine can not see the heat. This is most commonly caused in these Ricoh's by thermister failure. The thermister is a small electronic part that reads or monitors the temperature of the heat roller. The thermister fails, the machine fails to see the machine heating up and pop goes the SC542. The thermisters are pretty in-expensive at around $20.00. The expensive part is usually the labor to have a tech come out and change them.
Good Luck and Thank You for using Fixya.
WheatlandServices
My ricoh 2015 ask user
You can see the existing user codes in this machine please fallow the procedure:
press usertoos/Counter button - then go to system settings and press ok button - go to key operator tools and press ok button - go to address book managment and press ok button - it will ask you the one search number give 001 and press ok button - it willask you name or displayes existing name simply press ok button - it will display an other window their you con find the user code option please press the user code button you con see the existing user code the exit and use that code to use the machine.
Other wise if you want to remove the user code option go to usertools/counter and go to systems settings and go to key operator tools and go to user code managment and sellect OFF by using up/down arro key and press ok button and exit switch OFF/ON machine directly come to copy mode- thanks
I cant find the scanner
the copier does not use driver
u need to connect it using network cable (cross over if its only to one computer)
assigne ip address subnet mask and gate details
connec to the copier via ur web brouser ising that ip address
log in user name admin no password
go to address book and set up a user and the path to where u wana save
plus domain name workgroup all authenticatin detail and have a shared folder on ur computer with read and write rites enabled
sorry to say this but if u r not fammilia with connectivity side of things ull find it very difficult
I have an SC_542 error
fuser error temperature over /under
ull need service engineer to reset it
or new lamp,thermistor or thermostat
Not finding what you are looking for?