20 Most Recent Belkin Wireless Surf Router (F7D2301) - Page 3 Questions & Answers

This is the wireless access code, that they are referring to.... here are the settings, generically, but each router

Wireless Router

It is usually easiest to run the install wizard, but be sure to be ready to set the items listed below.

Things to set:

Note: Routers are intended to be set by geeks. You have to SAVE EVERY page, or the changes will be lost. A geek knows this (apparently). The router gives no protest...just dumps your changes.

1. Login password (RECORD THIS!!). Consider taping to bottom of the router. Physical access is not the security issue.

2. Set a recognizable system ID.

3. Invoke wireless security of at least WEP.

a. Assign your own access code, 10 digit home or cell #. Consider taping to bottom of the router. Physical access is not the security issue.

4. Check that your router is set to broadcast its' presence.

I would reset the router, as long as you do not have any complicated parameters set (static routes, port forwards, etc).

Hold the reset button on the back down for 30 seconds, continue to hold down while you unplug the unit, hold for another 30, plug back in and hold for another 30 seconds.

Restart the setup and see if you get anywhere.

Type 192.168.2.1 in your internet browser, and mess around with the settings. like the firewall on the ps3. You can find the ps3 IP under system information. The router more then likely named your ps3 by its ip. then look up a video on how to port forward your ps3 with your router.

If it is like restarting, call 18002235546 for Belkin.

If you don't remember it, you get to generate a new one. They're hidden. IIRC they are case sensitive and can be from 8-42 or so characters. Next time, write it down, because that's the only way you can duplicate it.

Logging into the router and selecting the wireless security tab gets you there.

Carl

I can't either :-)

However, my router is accessed by typing just 192.168.1.1 (my gaveway address) directly onto the URL bar.

If your computer is working on the internet and you are in the same network as your router, try it.

Carl

Open the router interface (192.168.2.1), by connecting a computer hard-wired to your router and ensure modem is also connected.
On the far left side, Click on Firewall and disable it.
Click on DMZ under firewall and assign an IP: 192.168.2.25 after enabling DMZ.
Assign the IP settings manually on your X-Box too.
IP: 192.168.2.25
Subnet mask: 255.255.255.0
Gateway/Router: 192.168.2.1
Assign DNS settings manually on your X-Box: Primary: 4.2.2.2; Secondary: 4.2.2.1
Click on Wi-Fi Protected Setup, disable this feature.
Click on Security under WIRELESS, change it to 64-bit WEP and enter tour phone no. as wireless key under key1.
Check if the firmware version on the router is: 1.00.17, else upgrade it.
Save the router settings.
Restore the router to factory defaults
Restore the saved settings on the router now.
Unplug the power from modem, router and X-Box.
Connect power to modem 1st, router 2nd and finally X-Box and now check.

For further clarifications, please revert!
Thanks for asking.

Regards,
Arvind S Iyer

use the reset button on the back to regain access again connect again using Here are the recommended steps to connect to a wireless base router 1. Check and remove power from both your router and the DSL ROUTER/CABLE ROUTER MODEM 2. Wait one complete minute until applying power to modem then wait one minute before applying power to wireless router. 3. Ensure you have green lights across both devices, specifically, the recieved and sent lights. These same lights will tend to blink rapidly when there is active data, at times this will still blink, and a DNS error will prevent you from connecting to the internet. If this is the case, call your ISP Internet service provider 4. Check your authentication Security key on your router first, then check all your wireless devices to ensure they are on the same network name, key, and channel with the same type of encryption as the router 5. Start one device at a time and check for connectivity, if your still experiencing a problem, check the settings on all your wireless adapters, device drivers, internet browser settings, firewalls and proceed. 6. still have problems, connect a rj45 cable from the router directly to your computer to at least see if your wireless settings are bad or if the router may be bad. 7. Contact your ISP to determine if your receiving singal 8. Avoid using a splitter or parital power backup for yours routers 9. Still having problems, change your wireless router only after your ISP changes their faulty modem 10.Attempt the same process when setting up your new wireless router and or modem

hi

IS THE LIGHT IS BLINK RED MEANS YOU DONT HAVE A PHYSICAL CONNECTIVITY.
PLEASE CHECK YOUR MANUAL AND YOUR CABLE CONECTIONS.

STEP1

TURN OFF ROTER AND MODEM
STEP2

CONNECT MODEM CABLE TO WAP PORT ON ROUTER AND LAN CABLE TO PC OR LAPTOP

STEP3

NOW TURN ON FIRST MODEM AND AFTER A 5 MINUTS TURN ON ROUTER, YOU WILL SEE LIGHT IS TURNING ORANGE AND AFTER THAT GREEN

READY NOW JUST ENJOY YOUR ROUTER.


ADVISE:

DONT INSTALL THE CD SOFTWARE DO ALL MANUALLY.

FOR GO IN TO YOUR ROUTER SETTINGS PLEASE LOG IN IN THE INTERFACE USING 192.168.2.1 OR JUST WRITE HTTP:// ROUTER

ANY QUESTIONS PLEASE TX ME .


TECHBELKIN

PS3 And XBOX :: BELKIN



Step 1:Connect Modem - Router - Computer (Wired)

Step 2:Open Router Setup by typing http://192.168.2.1 on the address bar of internet explorer

Step 3:On the Left click firewall

Step 4:Leave the Password blank and click submit

Step 5:Disable it and click apply changes

Step 6:Scan and connect in the Xbox/PS3/Wii

Step 7: Get the IP Address of the Xbox/PS3/Wii

Step 8:Open Router Setup in the Computer

Step 9:On the left under Firewall Click DMZ

Step 10:Enable the IP Address of the Xbox/PS3/Wii in it

Step 11:Click Apply Changes

Step 13:On the left Under Utilities click System settings

Step 14:Scroll down to the bottom

Step 15:Enable UPnP

Step 16:Click apply changes

Step 17:Test the connection ,Check the NAT

If working then let me know

==============================================
If it is still not working

Open Router setup

At the middle Under internet settings check the WAN IP

IF it starts with 192.168. or 172.16 Then you will have to contact your internet service and ask them to bridge the modem

The device you are trying to connect with ie the client. doesn't support WPA. Not all devices eg. Gameboys support the more advanced WPA standard. The trouble is you will have to downgrade your entire network to WEP just to accommodate the device that isn';t connecting... I wouldn't do it.. or do it just once to get an update or something like that. I'd leave the network the way it is...

You need to configure your router with below method. Connect your router to computer with ethernet cable then you can access it with following default link. http://192.168.1.1 or http://192.168.0.1 or http://192.168.15.1 or http://192.168.2.1 If you are not able to access it with above ip then check your computers ip address gateway ip is your router ip try with it. Then it ask for user name and password. Type user as "admin" and password as "admin" or "password" or blank. Then you can see configuration page of router. If you are still not able to access router with above ip then you need to RESET it for that press RESET button for 10 seconds it is in back side of router then all settings defaults..Then you can access it with above method. Then set WAN settings as internet service provider settings enable DHCP. . Then click on wireless->wireless security->WEP security there is code password note down it or enter new password then save setting s and restart router. then you can connect wireless with new password. Let me know if you need further assistance. Thanks for using FixYa.

Hi,
You may have malfunction driver on your computer. Please re install it as necessary.

You can access your router with below method.
Connect your router to computer with ethernet cable then you can access it with following default link. http://192.168.1.1 or http://192.168.0.1 or http://192.168.15.1 or http://192.168.2.1 If you are not able to access it with above ip then check your computers ip address gateway ip is your router ip try with it. Then it ask for user name and password. Type user as "admin" and password as "admin" or "password" or blank. Then you can see configuration page of router. If you are still not able to access router with above ip then you need to RESET it for that press RESET button for 10 seconds it is in back side of router then all settings defaults..Then you can access it with above method. . Then click on wireless->wireless security->WEP security there is code password note down it or enter new password then save setting s and restart router. then you can connect wireless with new password. Let me know if you need further assistance. Thanks for using FixYa.

Glad to have been a help even if it was just by asking questions!

If my comments were a help, please rate this answer according to the comment that I posted above.

You will probably need to return the router back to factory defaults in order to run the setup program again on it.

To return the router to factory defaults, press and hold the RESET button on the back on the router for approximately 20 seconds. Once you've done this, unplug the power cable from the modem (not the router) for about 15 minutes. While the modem is off, go back through the setup for the router again.

After you've completed the configuration of the router and waited the 15 minutes for the modem to clear its NVRAM, plug-in the power cord of the modem and let it sync to the network.

If all has gone well, you should then have a working router.

HI,

I got your issue, you must make sure the firmware is upto date in your router since in the surf wireless router we have the issue only because of firmware.

Click here to download the firmware.

Update it in the router using a wired computer, if you do it in a wireless comp, connection will be disconnected.

I'm sure this will work.

Good Luck!

Thanks in Advance!

Regards,
Prema.

PS3 And XBOX :: BELKIN



Step 1:Connect Modem - Router - Computer (Wired)

Step 2:Open Router Setup by typing http://192.168.2.1 on the address bar of internet explorer

Step 3:On the Left click firewall

Step 4:Leave the Password blank and click submit

Step 5:Disable it and click apply changes

Step 6:Scan and connect in the Xbox/PS3/Wii

Step 7: Get the IP Address of the Xbox/PS3/Wii

Step 8:Open Router Setup in the Computer

Step 9:On the left under Firewall Click DMZ

Step 10:Enable the IP Address of the Xbox/PS3/Wii in it

Step 11:Click Apply Changes

Step 13:On the left Under Utilities click System settings

Step 14:Scroll down to the bottom

Step 15:Enable UPnP

Step 16:Click apply changes

Step 17:Test the connection ,Check the NAT

If working then let me know

======================================...
If it is still not working

Open Router setup

At the middle Under internet settings check the WAN IP

IF it starts with 192.168. or 172.16 Then you will have to contact your internet service and ask them to bridge the modem


Regards
TOM

Hi,

Please see on the adapter of the router if the range of voltage is from 110 to 220. If it is then it is called auto-volt. The adapter can adapt whether 220 or 110. You can directly connect it to any socket.

If it is not auto-volt then you must use a step down transformer to use it.

Thanks.

regards,
longgee