20 Most Recent
Cellular Innovations HFBLU1K Bluetooth Headset - Page 5 Questions & Answers
Chrysler 2013 300c uconnect bluetooth is not working showing " Bluetooth pairing not successful". I can't even add new device.
There are a few things you can try to troubleshoot this issue with your 2013 Chrysler 300c's Uconnect Bluetooth system:
- Make sure that your phone's Bluetooth is turned on and that it is in pairing mode.
- Check the Uconnect system's settings to ensure that Bluetooth is turned on and that it is set to discoverable mode.
- Try restarting both the Uconnect system and your phone to see if that resolves the issue.
- Check the vehicle's manual to see if there are any specific instructions for pairing a device with the Uconnect system.
- If the above steps don't work, try clearing the Uconnect system's memory of previously paired devices, and then try pairing your phone again.
- Check if the software of the Uconnect system is up-to-date, if not update the software.
- Try deleting all previously paired devices on the Uconnect system, and then try pairing your phone.
If none of these steps resolve the issue, it may be a problem with the Uconnect system itself and you may need to take your vehicle to a Chrysler dealership for further assistance.
1/27/2023 9:04:07 PM •
Radio...
•
Answered
on Jan 27, 2023
Tvbp-btn wireless stereo headset. Cannot get it to charge & show blue light. Shows red light when plug into charger; light goes out approx 1 minute later.
If your TVBP-BTN wireless stereo headset is not charging properly and the blue light is not showing, there are a few things you can check to fix the problem.
- Check the charger: Make sure that the charger is functioning properly and that the connections are secure. Try using a different charger or USB port to see if that resolves the issue.
- Check the charging port: Make sure that the charging port on the headset is not dirty or blocked. Clean it with a dry cloth if necessary.
- Check the battery: Make sure that the battery is not damaged or dead. If the battery is damaged or dead, the headset will not charge.
- Check for software updates: Make sure that your headset's firmware is up to date, if there is any updates available, install it.
- Check the manual: Check the manual that came with the headset for any troubleshooting steps or contact the manufacturer for further assistance.
- If you have tried all of the above and the problem persists, it may be a hardware issue, and the headset may need to be repaired or replaced.
1/14/2023 10:26:47 PM •
Radio...
•
Answered
on Jan 14, 2023
Motorolla walkie talkie shuts off when PTT button is pressed... Driving me INSANE. Please help
This is usually a low battery issue. If you are using the rechargeable battery pack, does your Motorola unit accept regular batteries in place of the rechargeable battery? If you can put in 3 or 4 AA batteries (depending on the model), try that. If the radio stays on when you press the PTT button, then continue using the regular batteries or get a replacement rechargeable battery, if you can find one for the model. If the radio still turns off when you press the PTT button with fresh batteries, then replace the two-way radio.
I hope this helps. When the rechargeable batteries fail, they will still charge but they won't hold a full charge for as long a period.
Cindy Wells
1/14/2023 4:38:53 AM •
Radio...
•
Answered
on Jan 14, 2023
I have a sony wx gt90bt car stereo and I can only get the local station on am, the fm works just find.
I am not sure what type of car you have, but if it is reasonably modern, you will have what is called and "Active Antenna". This needs power and is usually powered from the car radio. I am sure that when the new radio was installed, this connection was missed. FM will work fine around town, but get a few miles outside, and you won't have anything. AM will be very noise or non-existant, as you have found out.
I had the same broublem with a used car that I had purchased. Once I connected the power to the antenna up, I had AM stations coming in from 200 miles away, and FM for 75 miles or so.
12/2/2022 6:11:33 PM •
Radio...
•
Answered
on Dec 02, 2022
How do i turn off blinking light after blueparrot is on
The blinking light tells you it is on and working it is also part of the setup process
The only two ways to stop it blinking is to shut down the headphones or dismantle the headset and disconnect the led
10/12/2022 12:50:40 PM •
Radio...
•
Answered
on Oct 12, 2022
Radio shack pro 2038
User Manuals are here;
http://support.radioshack.com/productinfo/DocumentResults.asp?sku_id=20-413&Name=Radio%20Scanners&Reuse=N
Best of Luck.
10/11/2022 4:03:53 PM •
Radio...
•
Answered
on Oct 11, 2022
How do I pair my bc-au-bs-206-bk speaker to my phone
Tip & How-To about Miscellaneous
Pairing Bluetooth Devices
Posters often ask "How do I pair my Bluetooth ???" Insert whatever device you have at the question marks.
Generally, you need to read the instructions for the camera, headset, speakers or whatever the Bluetooth device is.
Roughly speaking though.
Settings - Bluetooth - Search, on the Android, iPhone, Windows phone whatever.
With camera, speaker, headphones or whatever the Bluetooth device is, you have to press a button on that device to send out the signal. On my Bowers and Wilkins T6 Speakers, there is a button on the top with the Bluetooth symbol on it. This is the part people usually don't do and ask for advice, thinking it will do this automatically.
When the Android or iPhone device recognises it, click Pair, and if it asks for a code, the Default is '0000', (four zeros, no quotes).
Posted by ADMIN... on Nov 19, 2016
This manual is probably close enough for this fine Chinese device.
https://fccid.io/2ASLD-P17/User-Manual/User-Manual-4196764
VIDEO
https://www.google.com/search?q=bc-au-bs-206-bk+speaker+pairing
..
8/24/2022 1:55:57 PM •
Radio...
•
Answered
on Aug 24, 2022
Not finding what you are looking for?