20 Most Recent
Toshiba 2860 Copier - Page 5 Questions & Answers
How can I get the firmware for Toshiba e-studio 2830c ?
To obtain firmware for your Toshiba e-Studio 2830c, you can follow these steps:
- Visit the Toshiba website and navigate to the Support section.
- Enter the model number of your printer in the search bar and click on the search button.
- On the search results page, look for the Downloads or Firmware section.
- Select the firmware version that is compatible with your printer and operating system.
- Read and accept the terms and conditions of the download, if prompted.
- Download the firmware file to your computer.
- Follow the instructions provided by Toshiba to install the firmware on your printer.
It's important to make sure that you are downloading the correct firmware for your specific printer model and operating system to avoid any compatibility issues or other problems.
I have a Toshiba Copier is Blink SC C447 It need to Reset but but Service acess code #1048# is not un lock
The error message you're encountering could be due to several reasons, some of which are:
- Incorrect service access code: Make sure that you're entering the correct service access code. In some Toshiba copiers, the correct service access code might be different from #1048#.
- System lock: Some Toshiba copiers are designed to lock after a certain number of incorrect login attempts. If this is the case, you'll need to wait for a specified amount of time before attempting to enter the service access code again.
- Service access mode is not enabled: The service access mode might not be enabled on your Toshiba copier. You may need to contact your Toshiba dealer or service provider to have them enable the service access mode for you.
- Technical issue: The issue you're encountering might be due to a technical problem with the copier. In this case, it's recommended to contact a Toshiba service technician for assistance.
If you continue to have trouble resetting your Toshiba copier, it's recommended to contact Toshiba customer support for further assistance. They should be able to provide you with more specific information regarding your specific copier model and the issue you're encountering.
Toshiba e-studios 5540c C390 C3A0
The C3A0 error code in a Toshiba e-studios 5540c copier usually indicates a problem with the magenta color developer unit. The C390 error code is a general error code that is usually displayed when a specific error cannot be determined.
To troubleshoot the issue, you can try the following steps:
- Check the connections of all the units, including the magenta developer unit, to make sure they are securely in place.
- Clean the sensors and contacts of the developer units and the main controller board.
- Check for toner or other debris that may have accumulated on the sensors or inside the developer units.
- Make sure the developer units are properly loaded with toner and are functioning correctly.
- If the issue persists, it may be necessary to replace one or more of the developer units or the main controller board.
If you are not comfortable with these procedures or the issue persists, it is recommended to contact a professional technician
It's possible that the EPU tray may have come loose during transport, leading to a C390 error
Toshiba eStudio 2330c Firmware
You can try to update the firmware manually by downloading the firmware from the Toshiba website and following the instructions for installation. If you are still having difficulty, you can contact Toshiba customer support for assistance.
Toshiba e studio 455 error CDF0 . Change mot; Lgc board
The CDF0 error message on a Toshiba e-studio 455 printer indicates a problem with the laser unit. The error can occur due to a malfunctioning laser motor, an issue with the laser diode, or a problem with the laser control board (LGC board).
Here are a few steps you can try to troubleshoot the error:
- Check the laser motor. Make sure the motor is securely connected and functioning properly. If the motor is not functioning properly, it may need to be replaced.
- Check the laser diode. Make sure the diode is securely connected and functioning properly. If the diode is not functioning properly, it may need to be replaced.
- Check the LGC board. Make sure the board is securely connected and functioning properly. If the board is not functioning properly, it may need to be replaced.
- Check for any jammed or broken parts. If any parts are broken or jammed, they may need to be replaced.
- Check the manual of your printer and see if there are any specific instructions for troubleshooting the CDF0 error.
- If the above steps do not work, it may be necessary to take the printer to a professional for repair.
It's important to follow the manufacturer's instructions and guidelines when troubleshooting and repairing your printer. It's best to consult the manual or contact the manufacturer for specific instructions or guidance.
Toshiba 307 model photocopy Machain Error Code 0008
Error code 0008 on a Toshiba 307 photocopier typically indicates a problem with the fusing unit. This could be caused by a malfunctioning thermistor or a problem with the fusing lamp. It is recommended to check the fusing unit and replace any faulty parts. If the problem persists, it may be necessary to call for service from a qualified technician.
Error code C380 paper feed failure
c380 indicates auto-toner error for black developer (K).
Check following:
Is the harness between the LGC board and the developer unit drawer connector open-circuited?
Is any harness inside the developer unit or the auto-toner sensor harness open-circuited?
Is the auto-toner sensor connector or the connector CN341 on the LGC board disconnected?
IF connector no problems, then u probably need to replace the auto toner sensor.
F 101 13 toshiba error code 4508a
The error code F101 13 on a Toshiba e-Studio 4508A printer indicates that there is a problem with the fixing assembly. This can be caused by a number of issues, including a malfunctioning thermistor, a problem with the heating roller, or a problem with the temperature control system.
Here are some steps you can try to fix the error:
- Check the thermistor: The thermistor is a temperature sensor that is located near the heating roller. Make sure that the thermistor is securely connected and not damaged.
- Check the heating roller: The heating roller can become worn or damaged over time, which can cause the error. Inspect the roller for any visible damage and replace it if necessary.
- Check the temperature control system: Make sure that the temperature control system is functioning properly and that the temperature is set correctly.
- Restart the machine: Try turning the machine off and unplugging it for a few minutes before restarting it. Sometimes this can clear the error.
- If the error persist after trying these steps, it's likely that there's a hardware issue in the fixing assembly that will need to be repaired by a service technician. They will be able to diagnose the specific issue and repair or replace the necessary parts.
It's best to refer to the service manual of the copier/printer or consult with an authorized technician before taking any steps. An unexpected move may cause further damage.
Toshiba e-studio 452 error code c010 how to solved it
Error code C010 on a Toshiba e-studio 452 printer indicates a problem with the printer's fuser unit. The fuser unit is responsible for bonding the toner to the paper and can become damaged or worn over time.
To troubleshoot this issue, try the following steps:
- Restart the printer: Turn the printer off and then on again to see if the error message clears.
- Check for any visible issues: Inspect the printer and its components for any visible issues that may be causing the problem. This can include debris or foreign objects that may have gotten stuck in the printer, or damage to the printer or its components.
- Check the fuser unit: If the problem persists after trying the above steps, it is possible that there is an issue with the fuser unit. If this is the case, it may be necessary to have the fuser unit replaced by a professional.
If you have tried these troubleshooting steps and the problem persists, it is recommended to have the printer serviced by a professional. A technician will be able to diagnose the problem and determine the necessary repairs.
I hope this information is helpful. If you have any further questions or need additional assistance, please don't hesitate to ask.
HOW DO I CORRECT ERROR CODE C390 ON MY TOSHIBA ESTUDIO 3055C?"
Description:
Auto-toner sensor-C abnormality (upper limit)
Causes:
Auto toner sensor Harness LGC board Developer material
Remedy:
1 Developer unit • Check if the developer unit is installed properly. • Check that the developer unit and coupling on the equipment side are properly engaged. • Check that the mixer of the developer unit is rotated. • Check if the developer material is too dark visually. • Check if the amount of the developer material is too large or too small. • Remove any toner or dust on the ATC sensor connector and the drawer connector of the process cover. • Remove any toner or dust on the EPU sensor connector and the drawer connector on the equipment side. 2 Auto toner sensor Harness LGC board • Check the connectors and harnesses between the auto toner sensor and LGC board (CN365). • Check if there is any foreign matter such as toner in the connector of the auto toner sensor. Remove if there is and reconnect it.
How to fix toshiba photo copy machine not printing black and white but printing color and the black toner is full
If your Toshiba photocopier is not printing in black and white but is printing in color, there are a few possible causes and solutions to try. Here are a few things you can try:
- Make sure the machine is set to print in black and white. Some photocopiers have a setting that allows you to choose between color and black and white printing. Check the settings on your machine to make sure it is set to print in black and white.
- Check the toner cartridges. If the black toner cartridge is full but the machine is still not printing in black and white, there may be a problem with the cartridge. Try removing the cartridge and shaking it gently to redistribute the toner inside. Then, clean the contacts on the cartridge and the machine to ensure they are making good contact.
- Check the fuser unit. The fuser unit is responsible for heating and fusing the toner onto the paper. If the fuser unit is not working properly, it can cause the machine to not print in black and white. Check the fuser unit for any damage or debris, and clean it if necessary.
- Check for any error messages. If your machine is displaying any error messages, try to troubleshoot the problem based on the specific error message. You may be able to find the meaning of the error message and a solution in the user manual for your machine.
- If none of these solutions work, you may need to contact Toshiba for technical support or service. They may be able to help you diagnose and fix the problem with your machine.
Toshiba e studio 167 cannot use this size error how to fix it
Hi,
please power cycle your device and attempt to move forward. If error still persists, please alter the size of your paper to one that's appropriate for the printer or change the settings of the printer to allow for the paper size.
This would require you to reference the table of contents in the printer manual to follow the paper-size setup steps.
Thank you.
Toshiba 255 photocopier is powering off while running?
Hi,
Please double check that the printer isn't overheating because this might be a safety function activating due to high temperature. If this is the case, please lower the temperature from the a/c control in the room.
Also, please swap power outlets to rule out the first socket that you're using.
Thank you.
Not finding what you are looking for?