20 Most Recent Briggs & Stratton Briggs Stratton Pressure Washer Repair Manual B3277gs - Page 9 Questions & Answers

Check head gasket hopefully that is only problem.

One you need to look at your belt it is MST box do jack with it as you will bust the transmission your pulled may need look at a long with your belt you can ring me on 07849461942 I am in north Leeland thanks

You may need to look at your rings as the oil ring on the piston may need replace your rings could be done how old is the engine if you ring me on 07849461942

For some reason not getting fuel to engine. Check fuel filter, remove fuel bowl on carb. If full of gunk clean, rebuild or replace carb.

it wont turn over by hand? if so that is engine failure not very commom with Band S engines If you need further help, reach me via phone at https://www.6ya.com/expert/scott_8b3f0f0fc5f566a7

Briggs pn 594061

Hello:
Best to use NON DETERGENT 10W30. Be sure you fill the reservoir only 1/3 to less than 1/2 full.

Follow the link please for specs. http://outdoorpowerinfo.com/engine_specs/briggs_valve_gaps.asp

Sounds like your pressure pump is shot. Replace it. If you need further help, I’m available over the phone at https://www.6ya.com/expert/anthony_e4f197748c31eabd

Something is dirty in the fuel system. Sometimes I will start the engine and spray WD-40 into the air intake and keep the engine running with the WD-40 in hopes it clears out any debris. I would spray a half can. I’m happy to help further over the phone at https://www.6ya.com/expert/karl_14766549451f8563

Sometimes the hook at the end of the starter spring has broken off from rust or has straightened itself out. What I do if I don't have time to get a new spring is make myself a hook and attach it to the notch. Then you have to manually wind the spring in the right direction and hope that the spring doesn't unravel on you. Wear safety goggles for that! If I need to get it started without the recoil spring, I just wrap the starting rope around the engine and start it that way until I have time to get a new part. I’m happy to help further over the phone at https://www.6ya.com/expert/karl_14766549451f8563

http://diymaster.siterubix.com/change-oil-push-mower

The "spring" thermostat is a special spring, its made of special wire and set at a specific spring rate... if its damaged, over heated. by the muffler, etc.. replace it... Find Your Small Engine Owners Manual Briggs and Stratton Parts Lawn Mower Maintenance How To Briggs Stratton Lawn Mower Carburetor Repair Briggs Stratton

Try here https://shop.briggsandstratton.com/us/en/www-old/support/manuals

sounds like the carburetor is dirty. take it off and clean it real good with carburetor cleaner. clean the bolt that screws in to the bottom. there are small holes in it that are probably clogged up

I'm guessing you have a standard Champion J19LM plug, which has a gap of .030. They come pre-gapped from the mfg. and usually no need to adjust them. Most of the plugs on these engines have a .030 gap. There are very few exceptions that use a .020 gap (such as the RC12YC). Anyway, here's a link to a chart I like to use for reference: (there's a drop down menu at the top to change engines, but the standard Briggs engine is the one here). http://www.manddsmallengine.com/briggs/info/plug7.htmlHope this helps. James

Hi Lawrence. There should be a few more numbers/ letters to your model number. I added a link to a website for you to check out. Click the link or copy and paste it. Hope this helps. https://www.repairclinic.com/Shop-For-Parts/a22b303d782009/Model-42A7072653E1-Briggs-Stratton-Small-Engine-Parts