Life Fitness 95Ti Treadmill 95 Ti - Answered Questions & Fixed issues

If you wish to get some details treadmill repair and calibrations; check the site linked here. Pull up older posts. http://electro-medical.blogspot.com/

If you wish to get some details about treadmill repair ; check the site linked here. Pull up older posts. http://electro-medical.blogspot.com/

Replacement Parts for Fitness Exercise Equipment at SPORTSMITH I would suggest removing your heart rate grips and inspecting the contact leads for rust or any other corrosion. This is very commonly an issue and can be resolved by either cleaning the contacts or simply replacing the parts. Using the following link, and your serial number, you should be able to find the contact grips if you end up needing them. Repair Parts for LifeFitness 95T 95Ti 95Te Treadmills Midline SPORTSMITH...

If you wish to get some details; check the site linked here. Pull up older posts. http://electro-medical.blogspot.com/

Hi There, Give this a try....go to Sportsmith.net and/or google Service Menu Life Fitness 95Ti. Once in the service menu, there should be an entry for the user to select Miles or Km. It mentions pressing/holding the Pause Button until the Service menu appears on the display. Good Luck!

If the walking belt has shifted to the left, use the Allen wrench to turn the left rear roller bolt clockwise 1/2 of a turn; if the walking belt has shifted to the right, turn the left rear roller bolt counterclockwise 1/2 of a turn. Be careful not to overtighten the walking belt. Plug in the power cord, insert the key, and run the treadmill for a few minutes. Repeat until the walking belt is centred.

This could be caused by the smart stop mechanism being faulty or just simply unplugged. Smart Stop Assembly AK58 00064 0000 SPORTSMITH net

this occurs when the user is not walking on the belt to disable this feature you must press the option "select workouts" in the lower right corner press life fitness logo, when the menu appears in maintenance mode select the option user sensor and desactivate then exit the menu and ready

Please RUN the software calibration for easy diagnostic and fix it. Go under the HOOD and read the instruction and proceed. God bless you

then you should know this is caused by worn belt and deck

make sure you have not set to mph

belt and deck worn

when I start up my treadmilll across the screens reads Motor-comm error. what coulld be the problem.I keep it clean and dirt free.

my Life Fitness 95 Ti can not go faster then 10 km/h.Please advice

Adjust the REED switch , see the diagram attached and proceed according. clean it, test for open or faulty. and tight the connector very well. see the block diagram. Run THE software calibration for easy diagnose, and fix it.God bless you

you will call to the company for better instruction. They are obligated to supply instruction for fix the control board. Do not waste your time Call them right now.God bless you

No do not use, until YOU LUBE. This happen because you must do it every 5 hours aprox of use, The machine protect itself the electronic system and shut down.Maybe the deck belt is worn.2) LUBE the rollers bearing very i3) test the drive belt, and test too the bearint of main motor and fix it.God bless you

RUN the software calibration for diagnostic,, troubleshooting, and fix it.God bless you

1) Run the software callibration for diagnose and troubleshooting and fix it. Read your instruction manual, if you do not have go www.fitness.manualsonline.com or www. iconservice.comsee the block diagram for better understandingGod bless you

you must read you instruction manual, if you do not have download from www.lifefitness. com or www.fitness.manualsonline.com or www.iconservice.com read the section troubleshooting code.However you must do the following>1) Test the sensor see the diagram2) Lube the shaft and gear from elevation motor 3) Test the elevation motor 4( adjust the sensor and clean,and tigh the connector wires.see my personal TIPS for HELP. see the diagram attached.God bless you