20 Most Recent
Husqvarna Huskystar 215 Sewing Machine - Page 4 Questions & Answers
What corresponding # to use on the sewing machine to recognize the 3D programmable card.?
To recognize the 3D programmable card on the Husqvarna Rose sewing machine, you need to select the corresponding design number on the machine. The design number is usually located on the packaging of the 3D programmable card or in the software used to transfer designs to the card. Once you have identified the design number, enter it into the sewing machine using the keypad or touch screen.
I want to let you know that not all Husqvarna Rose models are compatible with 3D programmable cards. Check your machine's manual or contact Husqvarna customer support for more information.
How do I slow my Husqvarna Viking 18 x8 down. It stitches fast and faster, never slow.
To slow down the stitching speed on your Husqvarna Viking 18 x8, you can try the following steps:
- Check the machine's manual: First, consult the manual that came with your Husqvarna Viking 18 x8 machine. The manual should have instructions on how to adjust the stitching speed.
- Adjust the stitch length: One way to slow down the stitching speed is to adjust the stitch length. A shorter stitch length will slow down the machine's stitching speed. Refer to your machine's manual for instructions on how to adjust the stitch length.
- Change the foot pressure: Another way to slow down the stitching speed is to change the foot pressure. Reducing the foot pressure can help slow down the machine's stitching speed. Again, refer to your machine's manual for instructions on how to adjust the foot pressure.
- Use a different presser foot: Some presser feet are designed for slower stitching speeds. You can try using a different presser foot to slow down the machine's stitching speed.
- Use a speed control pedal: Some machines come with a speed control pedal that allows you to adjust the machine's stitching speed. If your machine has a speed control pedal, try using it to slow down the stitching speed.
If none of these steps help slow down the stitching speed on your Husqvarna Viking 18 x8, you may need to contact a professional technician for assistance.
Where can i get a foot pedal for my husqvarna viking 1610?
A foot pedal for a Husqvarna Viking 1610 sewing machine can be obtained from several sources:
- Sewing machine dealers: Many sewing machine dealers, especially those that specialize in Husqvarna Viking sewing machines, carry a wide range of replacement parts, including foot pedals.
- Online retailers: Websites such as Amazon, Ebay, and SewingMachinesPlus carry a wide range of replacement parts for older and newer sewing machines, including foot pedals for the Husqvarna Viking 1610.
- Husqvarna Viking: You can contact the manufacturer Husqvarna Viking to find the nearest authorized dealer or to purchase parts directly from the company.
- Specialty stores: Some specialty stores that focus on sewing machine parts carry a wide range of replacement parts, including foot pedals for older and newer models of sewing machines.
My sewing machine won't zig-zag stitch
There is usually one source for this problem, and it's easy to fix. Take the end cap of your machine as if you were changing a light bulb. Now you are off...When you switch from straightstich to zigzag, the levers operate across and inside the body so that the needle shaft, you watch it going up and down, can also move sidesways (but only a few mm's (about 3/16 inch)) The needle shaft should both go left and right, freely. It is hinged at the top but half way down ththe shaft it "floats" in a two sided guide. This sounds complicated but it truly is NOT. What happens to neglected machines is that "gunge" forms in the sliding parts and stop the left and right deflections. You my need to prise open the shaft from it's guide to start with (be gentle) but a few drops of oil normally soon allows the needle shaft to slide side to side. When you can shake the needle shaft from side to side BY HAND (with the machine set in the zigzag mode) replace the end cap and start zigzaging. And in future oil your flaming sewing machine.....
My husqvarna diamond keep telling me that it needs to rest. When I touch ok it makes hum the says need to rest. It wouldn't start sewing g
There could be a few different issues that could cause your Husqvarna Diamond sewing machine to display a "need to rest" message and not start sewing. Here are a few things you can try to troubleshoot the problem:
Check the machine's power supply: Make sure the machine is plugged in and the power cord is securely connected to both the machine and the outlet.
Check the machine's threading: Make sure the thread is correctly threaded through the machine and the bobbin is correctly installed. If the threading is incorrect, it can cause the machine to stop sewing and display a "need to rest" message.
Check the machine's tension: If the tension is not set correctly, it can cause the machine to stop sewing and display a "need to rest" message. Try adjusting the tension and see if that resolves the issue.
Check for any debris or lint buildup: Lint and debris can accumulate in the machine and cause it to stop sewing. Clean the machine according to the manufacturer's instructions to remove any debris.
If you have tried these troubleshooting steps and the machine is still not sewing, you may need to have it serviced by a professional. It is always a good idea to follow the manufacturer's recommended maintenance schedule and have the machine serviced regularly to keep it running smoothly.
Just wanted to check troubleshooting ideas on the feed dogs. They seem to be engaged but not running fabric through when sewing
Check that the stitch length is set to make ~10 stitches per inch. This stitch is long enough to actually move the fabric. If the stitch length is set too short, the fabric will stay barely move and the needle will stitch almost in place.
Check that the feed dogs have not been dropped for darning or free motion quilting. In this position, they do not rise and are, therefore, unable to contact the fabric to pull it through the machine.
With the presser foot raised and using no fabric, hand rotate the handwheel and watch if the feed dogs actually drop down below the needle plate, move toward the front of the machine, then rise above the needle plate, and move toward the back of the machine. If the feed dogs are moving in this manner, then they are functioning properly.
Is there lint or gunk stuck in the feed dogs? This will restrict the ability of the feed dogs to grip the fabric.
Are the feed dogs worn? Are the little teeth worn so there are no sharp points?
What type fabric are you using? If it is very light-weight or slick fabric, the feed dogs will have a difficult time gripping the fabric. Most machines have a presser foot pressure adjustment so that more pressure is applied between the presser foot and the feed dogs. Consult your Owner's Manual. The adjustment is usually a dial either on the left side of the machine, on the front of the machine located above the needle bar, or on vintage machines it is usually a skrew located under the top lid above the needle bar.
...
How to fix Husqvarna Viking embroidery when thread keeps clogging up under needle plate?
I had the same issue, exactly. I changed the cutter blades and it got much better. It is not totally fixed. It gets clogged most when the embroidery has to move around with the same color...which would suggest that it is still not totallly working. I think it might have to do with the cutter arm not retracting enough or not being positioned correctly. I'm still working this, but I hope that it helps you. If you found an answer, please share! Thanks!
My Husqvarna Designer SE limited edition feed teeth won't move.
I have a machine with the same problem. I have an additional problem too, my zig-zag also does not work. I'm thinking the mother board is bad because both forward stitch and zig- zag stitch use a stepper motor, so the stepper motors are not receiving commands to move into position. Thus making me think the circuit board or boards there are two, are bad.
So, does your zig-zag work? If so, then maybe you have one stepper motor bad, the stitch length one
Not finding what you are looking for?