Top 20 Sony KDL32BX300 32 in. TV Questions & Answers

Hi man 1 Look I don't know anything anout these "boards", etc. Might I suggest that before you go into "BIG Bucks" Have you checked for eliminating possible things that can interfere with your HDTV. I'd suggest that you examine the lines that go and input your picture as a possible issue. I had this with my PC HD Monitor, simply by overlaying power cables, ethernet lines, or even power cords from things nearby. Also, if you are on the 1st or 2nd floor, what is under you ? Is there a fluorescent light box, proximity to the circuit breakers, you see what I mean? Usuall these HDTVs are very well made, & changing parts is "unusual", but hey I could be totally off 100% on this one. My name here should be " CHARLIE CHEAP" !! I hate parting with my dough, and when there's a problem, it's amazing how often "the darndest things" happen, that normally we'd never think of. I sincerely wish you good luck, and "Low to NO costs" ,OK? Geoff

Dear Ing You need to load new software on your board - this to enable the main board to read the LCD Panel ID in the set. Go to your local SONY website and search for a download for this software, make sure you download the correct software on to a USB drive. Unzip the file and keep the folder in the root of the USB. You can now delete the ZIP file and check that you have the bin file in the folder with the software. Insert the USB in the back of the set. Make sure the set is off while you do this. Insert the power socket into the wall socket. Check that the light on you USB drive starts to flash ( Twice ) now switch your set on and wait. You will see the green and amber lights illuminate to show you the software is downloading. The set will switch of after more or less three minutes, now the amber and red lights will illuminate as the set unpacks the data and the set will switch off again and reboot to execute the software. Once the set asks you for the language selection - You have been successful! Good luck!

The price of the screen only will cost around 2/3rd of the total cost of a new TV.

It sounds that the main board has the fault. Checking and locating the faulty component to this board, is a very skilled work. Products powered by electricity should be serviced or repaired only by experienced professional technicians. Any attempt to service or repair the product by anyone else could result in serious injury or death. If you are not familiar with electronics, do not attempt to repair. Whether you suffer fatal electrical shock. Instead, contact the nearest service centre.

Any standard headphones with a 3.5mm jack will be compatable to the audio out.

The main power regulator board has damaged. Check and replace it.

if no stand by light indicator, it was a power supply board failure. check for blown primary fuse .

Time for a new TV---cost of just the part alone wholesale is more than another set---A lot this size the Panel or screen unit is not even available.Sorry but this is the case.

what do you mean how is the speakers hucked up

HelloPart Number for 32" LCD panel is [1-811-059-11] (S32TSP)Part Number for 40" LCD panel is [1-811-060-11] (S40TSP)

Tries tv and those Cables,Satalites or Telicoms pay boxes unplug,replug it back like about an hour later.Ur tv now should do a resetting itself back to the factory setting.Those pay boxes will reboot and updated it softwares.Ur tv should have incomming broadcasting tv chanels signal know.If u still have the same problems call ur tv Cables,Satalites or Telicoms compannies for a fix.

Hi there,

You need to reset the TV to factory defaults, then run through the initial setup again and make sure you choose HOME and not RETAIL as the location on the second screen of the setup.

To reset the TV to factory defaults:

1. Switch on the TV
2. Hold down the UP arrow key on the Sony remote control
3.While stillholding UP, press the POWER/STANDBY button on the front of the TV once.
4. Release the UP button

The TV will switch off and back on again. You will lose all of your settings and you will need to run the automatic channel scan again, but you will be able to select HOME as the location this time.

Please note: This question is listed for Sony TV model number KDL-32BX300. If you have a different model the reset method may not apply to you. In this case, try it once and if it doesn't work, please post back with the correct model number.

Hope this helps - please reply to me from within this page if you need further assistance.

Regards,
BElectric

Hello, you need to make sure what is broken, the remote control or the TV. To check the integrity of the remote control, you need to broadcast from the remote control while he aimed at the video camera. If you see a flicker of light through the camera it shows the integrity of the remote control. In this case need to fix the circuit of the infrared receptor. If the remote control out of order can be opened carefully by a thin screwdriver, usually the causes to the error are loose components or contacts that are supposed to weld back into the board. I hope it was helpful!! let me know if you need further assistance.

Try the following links:

http://esupport.sony.com/CA/perl/model-home.pl?mdl=KDL32BX300&LOC=3

http://esupport.sony.com/CA/perl/model-documents.pl?mdl=KDL32BX300


This one is a direct link to the User's Manual:

http://www.docs.sony.com/release/KDL22BX300.pdf

Good luck and please comment back and RATE if this was helpful.

Hi,

Yes you can. If it's exactly 4 hours, then you need to change the "Eco" power settings as follows;

1. Press the "MENU" button on your Sony TV remote control.
2. Use the circular arrow keys on the remote to highlight the flower icon for the "Eco" settings:


3. Press the large "+" key on the remote (in the centre of the arrow keys) to open the "Eco" menu.
4. Use the DOWN arrow button to highlight "Idle TV Standby". (The current setting will be 4h)
5. Use the LEFT/RIGHT arrows to set the value to "OFF" (1h or 2h can also be set).
6. Press the "MENU" button again to close the menu and return to watching TV

Hope this helps. Please post back if you are still unable to disable this feature or need further assistance.

Regards,
BElectric

Tries tv unplug,replug it back about an hour later.The tv now is resetting back to the factory setting.The tv should be working again now.If have the same result.The tv power supply board is the causes and the problems.That the board,where the power a/c cord plug into it.Tries websites like Shopjimmy.com,Ebay.com to buy a refurbish power supply board for the replacement.

Defective set. I would return it immediately.

have you hooked the yellow to yellow and the red to red and the white to white that should fix your issue

i have a Sony Bravia KDL-32BX300 the screen is cracked and broken where can i find a replacement screen

The problem in most of the case are: 1. Interference from a defective fluorescent lamp at your room sending signals to the infrared receiver of the TV. 2. Defective infrared receiver itself that sending noisy control signals to the CPU. 3. Defective manual control withes it has leakage. 4. Water damaged control switch PC board.