20 Most Recent Kenmore 24 in. 16352 / 16354 / 16359 Built-in Dishwasher - Page 5 Questions & Answers

you can find that on sears website but i dont think thats a valid model number

VERY CAREFULLY

The impeller isn't the motor, it's the impeller. If the motor was loud, it was the motor that needed servicing, not the impeller. Take the motor out and check the bearings on both ends of the motor. Run the motor out of the dishwasher before you put it back.

The cycle timer could be stuck and will have to be replaced.

The pump not pumping in the dishwasher. Check it for obstructions. Test it with a test meter. Replace it.

Correct

Could be a cycle timer problem

Could be a defective cycle timer

Contact searspartsdirect.com

hello there and welcome to fixya Could you tell me if the machine has this issue right before the mid cycle rinse or just after this and does it have any noise or does it just shut down There are a few things you can check I will walk you through each step as we go ok I just need a little more detail.

Common solutions for: Kenmore Dishwasher will not start. The door switch prevents the dishwasher from running and working while the door is open. If the door switch is defective, the switch will stop the dishwasher from running even when the door is closed. If the thermal fuse has blown , it will prevent the dishwasher from starting. Make sure your dishwasher is fully and also securely plugged in and that the circuit breaker switches haven't been tripped. .It also houses the door latch switch that provides the power to the dishwasher controls. If the dishwasher door isn't closed properly, the dishwasher won't receive power to finish a wash cycle You could call a repair person that fixes dishwashers to have a look at it and see what the problem is with the dishwasher

Hi,

My Kenmore Elite water softner won't allow me to adjust salt level anymore. I filled up to level 7, then tried to add salt level nothing happen. I tried to push the minus sign to see if it works, nothing. What should i do? Now i have flashing light indicates low salt level eventhough the tank is full.

find attached manuel for your machine

https://www.searspartsdirect.com/model/3cvirvbwnm-000582/kenmore-66516572200-parts

Pre-wash may be compromised and a new power circuit board may be needed. My advice: As long as the other cycles are accurate and work as usual; Pre-wash in your sink (spray off waste material) before you place the dishes in the washer and commence cleaning. Its best to wash off food and other material before washing in the machine to avoid clogging the drains and pump.

When the clean light flashes, it indicates a problem with the heating element or that the control board isn't getting the change in water temperature information in the expected period of time. Sometimes this is caused by a problem with the thermistor or thermostat. It could also be caused by a problem with the door switch or motor. Try cleaning the area around the latch and draining the washer after putting water in the tub. After that inspect the element for pitting or discoloration. Replace it if it is damaged. Check the resistance across the thermistor to ensure that the part is good. Check the wiring between the motor, thermostat, and heating element to the control panel for continuity and replace if there is a problem. If the rest of the parts are good, replace the control board. The parts list, diagram and pricing are available here: https://www.searspartsdirect.com/model/5umy9dy54i-000582/kenmore-66517033401-dishwasher-parts . Another parts list is available here: https://www.repairclinic.com/ProductDetail/939926 . I hope this helps. Cindy Wells

https://www.youtube.com/watch?v=BRGee1nRjO4 https://www.youtube.com/watch?v=rFgoZiCFWkY https://www.youtube.com/watch?v=rO19zoOyNHA https://www.youtube.com/watch?v=LaE3TFsZNSg https://www.youtube.com/watch?v=822fv_8TIus https://www.youtube.com/watch?v=fy1vRLNSd-Y https://www.youtube.com/watch?v=aYpybTpA1IE

check it has salt in the bottom tank. check the out pipe is not blocked or bent/twisted. check water feed is working and the filter in the line is clear. ( filter is in the machine side of the pipe you need to turn off water and remove the pipe at this end to get to the filter)

Faulty door switch?

Remove lower basket and try again