20 Most Recent Mitsubishi WD-65C9 65" DLP HDTV - Page 9 Questions & Answers

It sounds like you need to re-adjust your convergence. The purpose of adjusting your convergence is to align your red, green, and blue colors. Moving your TV often causes this problem. I hope you get it going.

Service Manual Mitsubishi Projection TV Chassis V20A Mitsubishi WS 65807 Error Code 22 Short Protection

If the lamp is new and good to go then you may have to reset the lamp replacement counter in your setting menu. When that is set back to zero you wont have a problem until it is time for a new lamp again.

Basically, all you need is: 1- Power-up the camera. 2- Select video input 1 or 2 on your TV. 3- Run a cable from the camera to the TV 4- Connect the cable coming from the camera to video input 1 or 2 on your TV. Please note: The cable you run from the camera to the TV has 2 Ends. One End connects to the camera (BNC plug) the other End connects to the TV (RCA yellow plug) I hope this helps. If not, provide the model# for the TV and camera, and if I come across your post I will be Happy to contribute. Best of luck www.aaatvservice.com

Might be tuned to the wrong output. The big tv has more than one input and is select able. Is there a blue ray selection for TV or input for that device.

It is helpful to have the sequence of the blinking red light. This may help:MODELS: WD-52627 / 52628 / 62627 / 62628 / 62827 / 62927 / 73727 / 73827 / 73927Page 433. Error Code Operational CheckNote: The TV must be in "Shut Down" and not have been switched Off, to perform the Error Code OperationalCheck. When the TV is switched Off, the code automatically resets to "12" No Error.Pressing the front panel "DEVICE" and "MENU" buttons at the same time, and holding for 5 seconds,activates the Error Code Mode. The LED flashes denoting a two digit Error Code, or indicating no problemhas occured since the last Initalization.Note: The front panel buttons must be used, NOT those on the Remote Control.• The number of flashes indicates the value of the MSD (tens digit) of the Error Code.• The flashing then pauses for approximately 1/2 second.• The LED then flashes indicating the value of the LSD (ones digit) of the Error Code.• The Error Code is repeated a total of 5 times.Example: If the Error Code is "23", the LED will flash two times, pause, and then flash three times.4. Error CodesThe Error Code designations indicating malfunction, or no malfunction, are listed below:POWERLEDSTATUSLEDLAMPLEDPowerStatus ConditionOff Yellow Off LowPower Excess heat. Check Lamp FilterOff or On Off Yellow Nochange120w usage time over 7000 Hrs.150W usage time over 3500 Hrs.Off Off BlinksYellowLowPower Lamp Cover openOff BlinksYellow Off " Filter Cover OpenOff Off Red Stby Lamp did not turn OnOff BlinksRed Off LowPower Fan StoppedOff Red Off " Circuit failure (short or DVIconnector unplugged)Abnormal LED IndicationsError Codes "DEVICE" & "MENU"Error Codes Description12 No error detected22 Recovery from Reset32 Lamp cover is Open34 Lamp abnormality35 DM Fan failed (Chassis Fan)36 Exhaust or Lamp Ballast Fan failed37 DMD Engine Fan failed38 Lamp temperature abnormally high. Remove Lamp to check filter.39 DMD temperature abnormally high41 Short is detected (Standby Power Supplies)42 Lamp Fan failed44 DVI cable between Format and Engine disconnected46 DMD Temp. Sensor not detected (check DT connector))47 DM Temperature too high48 Engine power supply short detected51 Speaker Drive circuit short detected52 HDD excess temperature (V30+ & V31 only)55 HDD Fan Stopped (V30+ & V31 onlyt)

Part#: KIT-MIR 767D084020 try this web site: https://www.encompassparts.com/item/7615765/Mitsubishi/KIT-MIR_767D084020/Kit-mirror_767D084020 or http://mitsubishi-tv.com/support

Try a new lamp. You will need the model# to locate the proper part# for your unit.

Hello: From the sound of your description of your problem you likely have a defective lamp. Feel free to give us a call at 866-764-5822 and we would be happy to help you troubleshoot the problem over the telephone. Best Regards Dan DLP Lamps Projector Lamps Specialty Lighting

Condensor? or just the projection lens. Condensor is just a lens like pice of glass used you distribute the light of the lamp evenly.

When you replaced the lamp did you reinstall the cover correctly? There is a safety switch incorporated in the cover .

major circuit problem, time for a flatscreen