When a Panasonic Blu-Ray recorder (DMR) shows "BD 1" "BD 2" or "BD 3" on its display, it means the remote control is not paired with the correct device. To change the channel the remote control operates on, you need to hold the "1", "2" or "3" remote control buttons simultaneously with the "OK" button for more than 5 seconds. If you want to change the channel of the device, you need to go to the "configuration" options and change the device to "BD1", "BD2", or "BD3
There are a few possible reasons why you may be experiencing black and white video when playing DVDs on your Syvania SSD803 DVD/VCR combo. Here are a few things you can try to troubleshoot the problem:
Check the video settings on your TV. Make sure that the TV is set to display color and that the correct video input is selected.
Check the cables. Make sure that the cables connecting the DVD/VCR combo to the TV are securely plugged in and that they are in good condition. If the cables are damaged or loose, they may cause the video to be distorted or not display at all.
Check the DVD/VCR combo. Make sure that the DVD/VCR combo is set to output color video and that all of the connections are secure. If the DVD/VCR combo is not set to output color video or if the connections are loose, it may cause the video to be displayed in black and white.
Check the DVD. Make sure that the DVD itself is in good condition and that it is compatible with the DVD/VCR combo. If the DVD is damaged or is not compatible with the DVD/VCR combo, it may cause the video to be displayed in black and white.
If none of these troubleshooting steps resolve the issue, it is possible that there is a problem with the DVD/VCR combo itself. In this case, you may need to have it repaired or replaced
There should be a small hole located on the face or on the side of it. Use a paper clip to stick in the hole. You will have to straighten the paper clip first.
If you only have the handset, if I remember, you have to unregister it from the base that was paired with it. If you haven't got that base unit, you are stuck.
The standard reset is to remove the battery for a couple of hours.
Plasma TV sets are impossible to get parts for. The problem that you are describing could be many things but the most likey is failing capacitors in the power supply
Hi,
You can replace parts but first I would check that your remote volume-down button isn't jammed because this might cause the volume to constantly be low or lower. I would also examine the volume-down button on your tv. Thank you.
These are for a Universal Remote. They might work. If not please add the remote manufactuer and model # to comments.
NEC TV 070 130 134 040 056 007 019 024 004 213
NEC VCR 012 023 043 048 039
Good luck, Techjoel
OR
Turn on your TV. On your Tune In remote, press TV and release. Press and hold Set until the green light on Tune In blinks once, pauses and then blinks twice. Now release the Set key. Enter the first three-digit TV code for your NEC from the list which follows: 030, 056, 019 These codes are listed in order of popularity, and the green light will blink twice if you perform this procedure correctly. Aim Tune In at your TV and press Power. Your TV should turn off. If it does not, repeat steps 2-5, trying each code listed in step 4 until you find the one that operates your TV. Now Test Your TVWhy test? Many times more than one code appears to work. Testing is desirable to be sure you have the correct code for your TV or the other devices you are setting up. Press the Power key to turn on the TV, then press mute, channel scan ("CH") and volume ("VOL") keys. Tune channels 7 and 11 by entering the number followed by the Enter key. If your TV does not pass the test, return to Step 2 at the top of this page. Enter the next three-digit code and repeat the process.
First try this. Does your player have a place to plug in ear phones or head phones? If so use this to see if you can get sound. Then we can work on next step.
