First you will need a pin out of the adapter.
Tools you will need are.
1: Solder with rosin core thin solder would be best
2: Soldering iron lower watts the better
3: Flux to clean the surface you want to solder to
4: Sponge to clean the tip of solder iron
If you don't have any of thous supply's it would be cheaper to buy a new cord. Also if you don't have vary much experience soldering i would also recommend getting a new cord for the fact you can cause more damage than good.
To get the solder iron ready you need to heat it up. Once it is hot enough to melt the solder apply the solder to the tip and let is set there until you want to solder. You have to clean the tip off with a wet sponge but not soaked in water just enough to get it wet. Every time you go to solder Clean the tip off and apply fresh solder to it not a lot just enough to cover the tip when you want to solder. When you go to store the iron apply a small blob of solder to the tip to keep it from oxidizing.
Strip the wire shielding off a bit longer than the size of the contact you want to solder. Twist the wire and put flux on the surface you want to solder and tin them.
Tinning the wire is just applying a small amount of solder to the wire as to hold the strands together and make it easier to transfer the heat and solder to the contacts. Now mach the pin-out to the weirs to the contacts and put flux on the contact you want to solder to. Clean the surface by applying flux to it.The surface will be oxidized and will not let you transfer heat or solder to the surface. The key to soldering is to use the right amount of heat , solder and time you hold the iron to what your soldering to. You want to make sure you touch the wire and the contact you are soldering to as to transfer the heat to both items at the same time to make the solder flow. Put the solder wire to the tip of iron that is touching the wire and contact and not on top of the iron tip. Any time you apply heat to solder joints you want to use flux to keep them clean and free of oxidized material. After you solder check the solder joints for cracks, uneven and dull surface. You want the solder to look as shiny as possible and smooth. If it looks like it has waves or holes and cracks it means you have a cold solder joint and must reheat and apply flux with a small amount of solder to fix it .Here is a link to help you out this is not my site and full credit goes to the owner of site. How To Solder Soldering Tutorial Also put a link to a new cord if you decide you want to get a new one. Here is a link that may or may not help with the pin-out. Also not mine it should credit the poster on the forum as he did all the work i just found it PSP Go Cradle mini USB Tutorial with Partial Pinout PSP Go Acidmods com
Hard Reset procedure for the PS3 (as instructed by Sony CS).
Be sure to backup your settings/games saves by doing a System > Backup on your PS3 or you may lose your game saves! Also, this is a last resort procedure prior to exchanging/returning to sony.
1. Power Off the PS3 via the power switch in back and power back on w/switch.
2. Hold Power Button on the Front until you hear 3 beeps.
3. Then go through the initial setup and then run a full Format via System > Format. (will take approx 3 1/1 hours). You may need to have our AV cables ready if your using HDMI (in case HDMI isn’t detected after initial reset).
4. Restore your backup you made prior to doing factory/hard reset (optional, if you created a backup).
Clarence, you are going to have to open up the stereo to manually eject the cd. There are several different models SONY has made of the "XPLOD" stereo. To make it easier for you, it would be a good idea to look on the back and note the serial number, or model number. For example, the steps to open up a touch screen "XPLOD" (XAV-63) is going to be different than a more standard (CDXGT150S). I hope this helps. Kick in some more info and I'll be happy to assist you further. ^^
Try doing the video reset. It seems to work the same for all SONY products. Hole the power down for a full cycle until it powers back off. I'm not sure if this will fix your issue, but it wont hurt to try. ^^ Good luck.
Brian, you are having an issue with your "
flicker" rate. You will have to adjust your frame refresh rate, or dpi to suit the connection you are trying to make. For example; Netflix works best at 720 dpi, but it will run at 1080. If you reduce the resolution, it will allow the LED's time to extinguish completely between the pixels. ^^ Hope this helps, and good luck.
Dallas, you have one of two options here. Either, you are able to repair your system using the Red Light of Death method (RLOD) or scrap the system and get a new one. I'll put in a link that explains the RLOD in detail. How to Repair YLOD Blinking RLOD On Your PS3
Pull the batteries out from the remote control, and leave it out until step-4
Press and release each and every button, one at a time on the remote control, until every button has been pressed and released at least once.
If the remote control have slide switches; move the switch to each position, then repeat the button pushing as in step-2. {When you've done, be sure to put the slide switch in the correct position to operate the unit the remote came with.}
Put the batteries back.
Try the remote.
http://electrohelponline.blogspot.com/
reset the xbox
look for how to reset an xbox360
i think its plug in hdmi etc
and press and hold the power button
then apply the mains power and wait 30 seconds
let it go and power off
then wait 30 sec and power on
there are many ways to reset an xbox...
you can ask the xbox whats up with it using the right keys
on the cd player
look up xbox360 diag
why did you ask for sony xbox360 questions
the topic isnt right
Get a camera with video, set it on record and start recording. When you feel you've recordedcall you want, stop. You should download your video to a computer through USB. If you like what you recorded, you can join it with other videos or just alone, burn it to an optical media:CD, DVD or Blu-ray
Hi there, I had the same problem, I tried a different hdmi cable, that didn't work so I rang playstation, seems to be some sort of problem with the database, so enter safe mode and rebuild the database, hope this helps.