For some reason, it is failing the self diagnostic tests. You need a service engineer, because the reason is likely the main control board. For that reason you need the correct diagnosis and warranty on the part and the work performed. This is not a simple fix. If the machine is old it may be prudent to just replace it.
If your Kenmore 70 series washing machine is not draining, check the drain hose for clogs or kinks. Ensure the pump is functioning, and inspect the lid switch for any issues. If problems persist, consider consulting the user manual or contacting Kenmore customer support for further assistance.
You start with under the agitator, then the filter, then the pump, then the hoses at the base of the drum and then everything else.
Then you find nothing and remember you took it out of your pocket and put it in........
..
Troubleshooting: Check the drain hose: Ensure that the drain hose is not clogged or kinked. If it is, straighten it out and remove any blockages.
Inspect the drain pump: Check the drain pump for any debris or foreign objects that may be blocking it. Clean it out if necessary.
Check the lid switch: Ensure that the lid switch is functioning properly. If it is faulty, it may prevent the machine from starting the drain cycle.
Check the waste hose: Ensure that the waste hose is not clogged. A clogged waste hose can prevent water from flowing out of the machine.
If this troubleshooting does not work, you may have to turn to professional assistance from a repairman.
The electric motor turns at a very high rate and as the brushes grip the commutator, they whine. The more weight in the machine, the more noise.
Normal.
Humming is the classic symptom of a Start/Run Capacitor that has failed. It gives the motor a jolt to get it going.
Just a little puzzled why spin works though :>/
..
If you find a tear in the hose or loose connection in the air pressure tube, then this is the likely cause of your F35 error code. If the air pressure tube appears to be okay, then you will likely need to replace the analog pressure sensor.
Jul 21, 2015
You were answering an AI Bot Chat GPT4 generated Answer, so we delete them.
Well done for fixing it
Testimonial: "Thank you just seeing this now. A couple of days ago I tore it all apart again. I checked the clutch and everything was fine. To my disbelief the coupler that I replaced 2 months, separated from the metal insert. So, I purchased one that was all plastic. I got everything working but it was shaking really bad on the spin cycle. I happened to see some stating to check the skate plate and sure enough it wasn't lined up. Everything is working great but there's still a slight vibration on the spin cycle. I think I will replace the 3 plastic pieces under the skate plate. All the springs look great so still not sure why it's unbalanced when spinning out."
..
If the exact answer using part number, from Kenmore or whirlpool, a good close answer can be found as
https://www.whirlpool.com › blog › washers-and-dryers › large-capacity-dryers.html Large Capacity Dryers | Whirlpool
Most standard dryers offer between 5.0 and 7.0 cubic feet of capacity. To help translate cubic footage into real-life laundry loads, consider that a 7.0 cu. ft. dryer can usually fit about 9-15 full-sized bath towels per load. Exact capacity varies by model so be sure to check the manufacturer's recommendations.
It could be the clutch or the gearbox. It can be repaired, but top loaders are old dinosaurs these days. Front loaders are as big or bigger, and more efficient and cost a fraction of the cost to run in water and electricity for heating that water.
Series 70 is just that, a series. A model number will give you the cost of spares and how many have been discontinued?
https://www.google.com/search?q=Kenmore+Heavy+Duty+Series+70+parts
..
There could be several reasons why this is happening. One possibility is that the timer or water line valve is faulty, which is causing the washer to stop mid-cycle. Another possibility is that the lid switch assembly has malfunctioned, which prevents the washer from spinning when the lid is open . Kenmore Washing Machine - Washer Stops Mid Cycle - Repair Parts ' Repair Clinic
I would recommend checking these components and their connections to see if they are functioning correctly. If you are not comfortable doing this yourself, it's best to contact a professional appliance repairman to diagnose and fix the issue