D-Link DIR-300 Wireless Router - Page 8 - Answered Questions & Fixed issues

try to reset by pushing the button in the back then run the setup wizard by accessing your routers page via the ip address if you do not know your routers ip address plug it into your computer with an ethernet cable open up your command prompt and type in ipconfig then enter and look for your default gateway

try unplugging the connection for the modem and router each for 30 seconds, then plug them each back in again.

First you need to verify that what kind of Internet connection you have from the satellite and what you need to do on the router so that it can communicate with the modem like MAC address cloning or changing the LAN IP Address. On the basis of that we will need to reconfigure the router back as it might happen due to a power outage or small network glitch the router might have lost the settings stored on it.

You will need to check the wireless settings of the router.
If your network is secured then make sure that you are typing the correct network key.
also make sure that the DHCP server is enabled on the router.
is there any computer connected to the router ?
If yes then you can open the router set up page on that computer.
Router set up page is the page where you can check all the wireless settings of the router.
Click here for step by step instructions

you will have cd with you router, use that cd to put password

Ensure that the router firewall is not blocking the http port 80.

Have you configured the router to open your utorrent port?

Have you set up specific strict rules?

Hello you have different level of security on it.
If it is open and without any security surely others will pirate and hack your Network system.
You can log onto the default IP is http://192.168.0.1
Specify user name and password for your router, the default is `admin' (optional) and password is blank (nothing). or at times it is ' admin '
There are 2 common mode of security that can be enable
1st is :WEP Encryption
2nd is : WPA-PSK Encryption
The wpa-psk is most stable and secure network
You can also use 128 bit encryption password
Hope this might help you
I am attaching link for manuals and downloads of the dir 300.
First link:
http://www.dlink.com.au/tech/Download/download.aspx?product=DIR-300&revision=REV_A&filetype=Manuals
Second link:

http://support.dlink.com.au/Default.asp
If you need further assistance revert back
Regards
uttam

If your computer keeps on disconnecting, then the problem could be caused by weak signal, electrical interference or interference with other wireless router broadcasting on the same channel. Please click on this link and follow my instructions for possible fixes :-
http://www.fixya.com/support/r3559120-wireless_router_disconnecting

start - run- type in cmd- enter- type in ipconfig /all will show router address should be 168.192.1.1
open internet explorer and type that # in the address bar
should connect with router
leave password blank or type in password for the password
enter the router setup and configure router to your preferance

it is PPOE,. That is standaed

please download it from the following link
http://members.driverguide.com/driver/detail.php?driverid=1532771

If a router was working flawlessly but suddenly stops working in the way you describe the most common issue are either connections that have become faulty [check wiring, swap out cables to see if any have gone bad] or settings/firmware have become corrupted.

If the latter bypass the router and go to the D-Link support site: http://www.dlink.com/support/

download the latest firmware for your router and follow the instructions provided for flashing the ROM to correct any corrupted code.

Remember to use the administrative functions through the browser access [usually accessed by typing this address: 192.168.0.1 into the browser for D-Link routers] to save all your settings to a file so you can replace them after flashing the routers ROM, for doing so will have reset those settings back to factory defaults.

Hope that helps.

just type 192.168.0.1 in the browser and the connect to the router.. make sure ur network settings are proper before u do that and then u can like configure the same

best of luck

If you connect the computer directly to the modem, does it work?
If that works then the modem is working.
Now connect the computer to the router and the modem to the router.
You will need to open the set up page of the router to check the settings of the router.
You can set up the router without the CD also.
It is very easy.
Click Here for step by step instructions about how to set up the router

The laptop that has trouble connecting to the wireless router, the wireless card in this laptop has not been configured with the router's wireless settings eg. the SSID, encryption key etc
Please click on this link and follow my instructions to configure and secure your wireless router and to configure the wireless card in the laptop:-
http://www.fixya.com/support/r3559128-wireless_router_security

hi i am techbuddies from fixya group and i want to help you

first of all i would like to tell you that the dns is domain name server of the computer that helps your computer to connect to the internet for this you need to contact your isp and they will give you the dns from their list ,
if you donot get it then please let me know i will give you some dns that can help you to connect to the internet .

thanks
techbuddies

Have you tried getting a slim object like a pen nib and poking the reset button, hold it for about 10 seconds and then release, it will take about 30 seconds to 1 min to reboot, this will do a hard reset and it will deleete all of your settings. that should reset it. Guy

After you click 'SAVE', the router will restart itself.
While it is restarting, it briefly disables its Ethernet ports,
and your computer will report "not connected".

Wait 60 seconds, while the router finishes its restart,
and those Ethernet ports will be re-enabled,
and the pop-up balloon on your computer will close itself.

Hi! I will be more than glad to assist u in this concern..Please dont use the setup cd or setup wizard. you can access the setup page of the router by typing at the url:192.168.0.1 then it will ask for the user name and password, by default the username is admin and the password, leave it blank.. here are the things u need to check before u setup u router.. .. if you are using a cable modem from ur cable company provider- u need to do a mac clone on the router u have to clone the mac address of ur computer. normaly the mac of ur computer is the one register to your cable company and on the setup page of the router just selct on the internet setup, dhcp after clonning the mac address of your computer. u need to connect ur computer directly to the router and then after doing the process connect the router to the modem. if u are using a username and password, u have to use the pppoe settings on the router, if ur isp set a static ip , set it up to the router, to check the ip setting of your isp.. connect the computer directly to the modem and check if u have internet.. then click on start, run and type cmd,it will give u a dos prompt and from there type ipconfig/all and it will show u the ip address, subnetmask, default gateway, dns server.. I hope this will solve ur concern..

First you might need to reset your router by pressing the tiny pinhole located somewhere at the back of the router. Once it was reset to default, you can plug it and open a browser with the url
http://192.168.0.1. Type admin as your username and password and you can be able to configure your router from the control panel.