20 Most Recent Belkin F5D8236-4 Router - Page 6 Questions & Answers

For that you need to reset router then configure again also make sure wireless is enabled. For RESET router press RESET button for 10 seconds then it reset all settings to defaults. then follow below. You need to configure your router with below method. Connect your router to computer with ethernet cable then you can access it with following default link. http://192.168.1.1 or http://192.168.0.1 or http://192.168.15.1 or http://192.168.2.1 If you are not able to access it with above ip then check your computers ip address gateway ip is your router ip try with it. Then it ask for user name and password. Type user as "admin" and password as "admin" or "password" or blank. Then you can see configuration page of router. If you are still not able to access router with above ip then you need to RESET it for that press RESET button for 10 seconds it is in back side of router then all settings defaults..Then you can access it with above method. Then set WAN settings as internet service provider settings enable DHCP. .Click on wireless and enabled it. Then click on wireless->wireless security->WEP security there is code password note down it or enter new password then save setting s and restart router. then you can connect wireless with new password. Let me know if you need further assistance. Thanks for using FixYa.

Hi,
In oder to reset the router password, look in the rear end of router you will find a tiny reset button push that reset button for 10 sec with power on then the router will go back to factory default settings.
Thanks & Regards, Prema.

Hello,

There are many reasons why this might be happening.. You could try the following steps..
1) Disconnect the power from router for a minute and reconnect and check.
2) Try changing the wireless channel and Network name and try re-connecting.
3) Check if there is an firmware update for your product and update if any update is available.
4) If none of the above steps work you will need to reset and re-config your router. ( For that you need the CD given with the router and you will need the ISP settings.)
Hope this helped

Hello,

Looks like it might be an issue with the security type on the router. Try changing the security type and network name, it might work.
(P.S. you might need to re-connect all the wireless computers if the security key or network name is changed.)

Hope this helped.

Connect your router to computer with ethernet cable then you can access it with following default link. http://192.168.1.1 or http://192.168.0.1 or http://192.168.15.1 or http://192.168.2.1 If you are not able to access it with above ip then check your computers ip address gateway ip is your router ip try with it. Then it ask for user name and password. Type user as "admin" and password as "admin" or "password" or blank. Then you can see configuration page of router. If you are still not able to access router with above ip then you need to RESET it for that press RESET button for 10 seconds it is in back side of router then all settings defaults..Then you can access it with above method. . Then click on wireless->wireless security->WEP security there is code password note down it or enter new password then save setting s and restart router. then you can connect wireless with new password. Let me know if you need further assistance. Thanks for using FixYa.

Hello cyndi0417.
If you have installed your router, and have a computer connected to it through one of the wired ports, you can follow these steps to find your WEP or WPA key.
Step 1.
Open a web browser of your choice, and in the address bar type in "192.168.2.1" (without the quotation marks).
Step 2.
Select "Login" from the upper right corner of the screen. Unless you have changed the administrator password, you can just click on the submit button.
Step 3.
Look under the "Wireless" heading on the left side of the page. There will be a selection for Security, which will contain the WEP or WPA settings. The numbers/letters in the boxes is your key.

There a great article at General Router Setup.
If you need more help post back!
Thumbs and testimonial are welcome!

There is a great article at Working with Windows Wireless Networks
If you need more help post back! Thumbs and testimonial are welcome!

There is a great article at Working with Windows Wireless Networks
If you need more help post back! Thumbs and testimonial are welcome!

WIRELESS SECURITY ISSUES

Step 1 : Connect Router - Computer ( Wired)

Step 2 : Open Router Setup by typing http://192.168.2.1 on the address bar of internet explorer

Step 3 : On the left under wireless click wi - fi protected setup

Step 4 : Leave the password blank and click on submit

Step 5 : Disable it and Click on apply changes

Step 6 : On the left under wireless click Security

Step 7 : Enable 64 Bit WEP

Step 8 : Type a 10 digit number on the key 1 ( 2 in each box )

Step 9 : Click apply changes

Step 10 : on the left under wireless click channel and SSID

Step 11 :Change the Wireless channel to 6

Step 12 : Change the SSID to a different name ( no Spaces )

Step 13 : Click apply changes

Step 14 : Now Scan and connect to this network ( Wireless )

Let me know if it works


Regards
TOM

There a great article at General Router Setup.
If you need more help post back!
Thumbs and testimonial are welcome!

Hi. This is a problem with wireless connrctions.
You need to turn on security on your router, and assign a security level and password.

Here is the link to the Belkin website with the instructions on setting up security on your Router.

http://en-us-support.belkin.com/app/answers/detail/a_id/33/kw/drivers%20F5D9236/related/1

These are Belkin's official instructions for all Belkin Routers, an none of them have a password asigned to them from the factory.

Here is a great tutorial to Connect and troubleshhot your Xbox to a wireless network.
If you need more help post back! Thumbs and testimonial are welcome!

check your router setup page (192.168.0.1 or alike, check on bottom of router or in router documentation) and see if you've turned off the wireless.

Hi!

You need to access the wireless settings of your router to check for the passphrase or security key

I can assist you with this.

Try this link

It will give you the quick install guide

Reset the router:

Step 1 Locate the reset pinhole on the back of the unit.

Step 2 With the unit powered on, press and hold the Reset button.

Step 3 Hold the Reset button for about 10 seconds.

Step 4 Release the Reset button.

Step 5 The unit will reboot. Allow 20-30 seconds before reconnecting.

Step 6 The device is now at factory defaults. Note: Do not recycle power during the reset procedure.

If I could be of further assistance, let me know. If this helps or solves the issue, please rate it and give a testimonial for my response. Thanks, Joe I’m happy to assist further over the phone at https://www.6ya.com/expert/joe_8b8c2cd6ce148309

WIRELESS SECURITY ISSUES

Step 1 : Connect Router - Computer ( Wired)

Step 2 : Open Router Setup by typing http://192.168.2.1 on the address bar of internet explorer

Step 3 : On the left under wireless click wi - fi protected setup

Step 4 : Leave the password blank and click on submit

Step 5 : Disable it and Click on apply changes

Step 6 : On the left under wireless click Security

Step 7 : Enable 64 Bit WEP

Step 8 : Type a 10 digit number on the key 1 ( 2 in each box )

Step 9 : Click apply changes

Step 10 : on the left under wireless click channel and SSID

Step 11 :Change the Wireless channel to 6

Step 12 : Change the SSID to a different name ( no Spaces )

Step 13 : Click apply changes

Step 14 : Now Scan and connect to this network ( Wireless )

Let me know if it works


Regards
TOM

try to reset it to default press and hold the reset button on the back if you are trying to log in to the router it self

1. Connect the computer to one of the four LAN ports on the router.
2. Open a web browser on the computer.
3. In the address bar of the web browser, type http://192.168.2.1
4. Click Login in the upper right-hand corner of the page. The router does not ship with a password, so just click Submit.
5. Restore system defaults.

was it working at one point whats the problem

This is a very unusual occurrence, but nonetheless, I know the answer! I'm assuming that the security button randomly turned on, meaning that you don't know the password that it may have set, right? My recommendation is giving it a factory reset, meaning that it will set the router back to ALL default settings. To do this, all you need to do is get a thin pencil tip, or a pin, and press and hold down on the RESET button, which can be found on one of the side panels of the router, for slightly over TEN seconds, then after holding it down for about 10 seconds, it should reset itself back to normal, and the security will be disabled. You can set up security again by changing the settings on the router homepage, which by default is located at "192.168.2.1" just type that into your URL search bar in your internet browser.