D-Link DIR-615 Wireless Router - Answered Questions & Fixed issues
Router just has an orange power light
Hi Challywags,
Normally if the router's power light is orange, red, or blinking there is problem with it's software/firmware. Or in some worst cases, it might also be a faulty unit already.
Here are things that you can try:
* Unplug it and wait for 1 minute before powering it on.
* Reset the router using the reset button. Note, this will restore the default settings configured in your router. You may need to reconfigure the router after doing this.
In case none of the solutions above will work, and none of these steps will turn the power light green I recommend that you contact the router's manufacturer for further troubleshooting. If the device is still under the warranty you will be able to get it replaced.
I am trying to get my D-Link set up for wireless
If you have a hard connection that is you have a cable to your router you can go to Dlink's site and watch the setup videos if you are not savvy with technical terminology.
there is also a site called Ehow that will educate an well as show how to utilize the wireless setup you have .
Please provide your model number , Operating system and more detail as to the issue you have so we can further assist you properly.
How to get password
The final solution is a factory reset of your router. You can do a factory reset by logging into the router using you browser. Go to the settings and perform a factory reset
If you forgot the router password, you ill have to do a factory reset by locating a small hold on the back of the router and insert the tip of of paper clip for about 10 seconds while the power is on. The router will be reset to out of box status and then you can set-up form scratch.
I want to log in to my d-link 615 but don't know
The final solution is a factory reset of your router. You can do a factory reset by logging into the router using you browser. Go to the settings and perform a factory reset
If you forgot the router password, you ill have to do a factory reset by locating a small hold on the back of the router and insert the tip of of paper clip for about 10 seconds while the power is on. The router will be reset to out of box status and then you can set-up form scratch.
Login in using your browser and go to the wireless settings and set-up a wireless password/key. Remember the key because each device will now need it to connect. You can also turn OFF Broadcast SSID and your network name will not be shown on anyone's device. You must remember the network name when using this method.
How to connect
You do not need the disc. Using you browser, login into the router using the default IP 192.168.0.1 unless this has been changed and you should be able to configure your router.
user ADMIN for login and leave password blank then you can connect using the wizards.
Login in using your browser and go to the wireless settings and set-up a wireless password/key. Remember the key because each device will now need it to connect. You can also turn OFF Broadcast SSID and your network name will not be shown on anyone's device. You must remember the network name when using this method.
Dir-615 all lights flashing
If a hard reset does not fix, then your electronics may be bad.
The final solution is a factory reset of your router. You can do a factory reset by logging into the router using you browser. Go to the settings and perform a factory reset
If you forgot the router password, you ill have to do a factory reset by locating a small hold on the back of the router and insert the tip of of paper clip for about 10 seconds while the power is on. The router will be reset to out of box status and then you can set-up form scratch.
FIRMWIRE FOR DIR-615 REV M2
Usually you can login on your browser to you router and go to the management section to check for firmware updates and select that button and it will download and install the firmware. On some models, you have to go to the D-link web site and look for firmware updates for your router. Always check what you current firmware you have installed and check the version of your router modem hardware (A, B, C etc). Then you can manually download the firmware (usually in a ZIP file), open the zip file, and then using your browser connected to the router look for Update Firmware. You will have to go to where (folder) you saved the downloaded update and select that file. It is recommended that you update using a LAN connection and not a wireless connection.
How can i make my wifi unlock on my D-Link dir 615 wireless router
Login in using your browser using a LAN cable and go to the wireless settings and set-up a wireless password/key. Remember the key because each device will now need it to connect. You can also turn OFF Broadcast SSID and your network name will not be shown on anyone's device. You must remember the network name when using this method.
How to rename
Login in using your browser and go to the wireless settings and set-up a wireless password/key. Remember the key because each device will now need it to connect. You can also turn OFF Broadcast SSID and your network name will not be shown on anyone's device. You must remember the network name when using this method.
How to secure network for DIR 615 so it can't be
Login in using your browser and go to the wireless settings and set-up a wireless password/key. Remember the key because each device will now need it to connect. You can also turn OFF Broadcast SSID and your network name will not be shown on anyone's device. You must remember the network name when using this method.
My laptop computer is no
Login to the router and see if the wireless was turned off and if so turn transmit on. Try rebooting the router. If not The final solution is a factory reset of your router. You can do a factory reset by logging into the router using you browser. Go to the settings and perform a factory reset
If you forgot the router password, you ill have to do a factory reset by locating a small hold on the back of the router and insert the tip of of paper clip for about 10 seconds while the power is on. The router will be reset to out of box status and then you can ssets-up form scratch.
Can I change my security key number
Login in using your browser and go to the wireless settings and set-up a wireless password/key. Remember the key because each device will now need it to connect. You can also turn OFF Broadcast SSID and your network name will not be shown on anyone's device. You must remember the network name when using this method.
Not finding what you are looking for?