20 Most Recent D-Link DIR-615 Wireless Router - Page 7 Questions & Answers

Hopefully you have the setup disk that came with the D-link unit when you bought it. If not, order it from D-link. Next., put it in your computer and follow the setup procedure...you will be able to take care of the password at that time.

You should be able to , that begs the question, is youe ISP "throttling" the signal? Is there a problem with the equipment. inside or outside? Have you checked ALL cables, reseated ALL connections, rebooted the ISP Modem, the wireless device?Is the wireless Secured? As you move about the house is that when you lose connection? If you are sitting next to the D-Link will it stay connected? It may be outside? Contact your ISP and have them analyze the signal, have a ISP tech come out and analyze.

Reset the device by pushing and holding the reset button for 30 seconds or so, release. This will reset to default settings. Reconfigure SSID and Security. You may want to write down the password for future use. This may help: ftp://ftp.dlink.com/Gateway/dir615_revC/Manual/dir615_revC_manual_300.pdf

Most likely you have damaged not only the power supply but also the D-Link wireless router unless the power adapter is a multi-voltage power adapter. Check the label on the power adapter and if the input voltage is a fixed 110 volt power supply you are in trouble.You can try getting a 110v power adapter and connect it into the D-Link and if it works then you are lucky.

Most likely you have damaged not only the power supply but also the D-Link wireless router unless the power adapter is a multi-voltage power adapter. Check the label on the power adapter and if the input voltage is a fixed 110 volt power supply you are in trouble.You can try getting a 110v power adapter and connect it into the D-Link and if it works then you are lucky.

Wired or wireless? Check all cables, have you tried to connect with a Ethernet cable to the ISP modem, if it connects, try connecting via the cable to the D-link. Work you way through the devices one by one.If it connects via the cable, it's the computer's wireless adapter. Will other computers connect? Or contact your ISP to verify the signal, have a tech come out to analyze the signal. It may be outside. It's happened before, to me.

Press what? If your wireless is working properly , just boot computer and connect. Try the user manual: ftp://ftp.dlink.com/Gateway/dir615_revC/Manual/dir615_revC_manual_300.pdf

LAN PORTS ARE BAD SEEMS TO BE.

check the manual for default passwords. If you have set up a custom password, not much help available. Good luck

To setup a network just follow the step by step guide that came with the DIR-615 router. When it comes to setting up the internet on the router wizard just select Cable or DHCP and leave the other internet settings as default. As regards to your printer we need to know the make and model number so we could further assist you. By knowing the make and model of the printer it will help us how to best setup your printer on the network. The model number is usually the name of the printer or near barcodes on the back or bottom of the printer.

you can ask virgin media to strengthen the range the wifi can reach I think the cost$ of router/wifi is dependent on its speed and range

If the default password on the D-Link has been changed then - To reset the D-Link back to the default settings - Press and hold the RESET button at the back of the router with the power ON until the LEDs flash at the time the release the RESET button. (firmware version was 3.00, and upgraded to 3.05) Connect a LAN cable from the D-Link to your laptop/computer's LAN port, open the browser on your laptop/computer and enter the D-Link's configuration URL.. http://192.168.0.1 The default login = admin The default PW = blank (just press Enter) You can now change the default admin password. You can now configure the wireless settings. (WPA or WPA2 encryption) Now configure the wireless card in your computer/laptop with the router's wireless settings. To secure your wireless network from unauthorized access, please click on this link and follow my instructions :- http://www.fixya.com/support/r3559128-wireless_router_security

Hold the reset in the back till it cycles. This will clear all custom settings. Like new!

Login to your DLink router through your web browser. Click the advanced tab.In the left column, click the Website Filter option. To block sites, enter their website addresses in the space provided (Do not add the http://). Blocking the websites at the router level ensures all traffic leaving your network will be affected by these rules. These include computers, smart phones, gaming consoles and anything else with a web browser.You can block websites with Dlink router or change the DNS settings in your router and use a service like OpenDNS to block websites. If you need any kind of technical assistance you can contact support cell at http://www.vtechsquad.com/

Test with network cable, and work backwards to ISP modem to find point of failure.

You will have to open up your network connections. Click start control panel network connections this may vary depending on your operating system look for local area connection if you see a red x or a yellow exclamation or question mark you will need to update or install the driver or it could be firewalled. Click start control panel administration tools computer management device manager look for network adapters + expand Ethernet driver if you see a yellow question exclamation mark ? ! or a red X you will need to update/reinstall the driver for the device Make sure you Ethernet/internet is enabled in bios. Restart your computer during the boot up process you will see on your screen a certain key to press to enter set up (BIOS) press and hold that key to enter bios using arrow keys scroll to intergrated peripherals look for SiS On Chip Pci Device press enter make sure its enabled then recheck the driveri t should be there k the driver it should be there make sure its enabledPci device arrows key scroll to nstalled if you computer came with a motherboard disk the driver could be on it or this disk provided by your ISP provider Internet Service Provider

or you might have to download one http://download.cnet.com/wireless-atheros-ar5b91-7/3000-2112_4-202570.html http://download.cnet.com/Realtek-RTL8139-Family-PCI-Fast-Ethernet-NIC/3000-2112_4-91313.html if these packages are not the right http://download.cnet.com/2000-20_4.html On the home page you should see a search tab just type in what you are looking for tick in the box for windows software or all software box IE: Motherboard name wireless or Ethernet driver you might have to try a few times to get it righthope this helps

Do you need a password? In Network and Sharing go to Manage Wireless Networks, Do you se your SSID for your wireless access point? Hightlight and remove, reboot your laptop, you will have to choose your SSID and re-enter your password. If that fails do a cold start on your laptop: unplug, remove battery, hold on/off button 10 seconds, replace battery, plug in start normally.

Re set to default by pushing and holding for 10 seconds the re set button. Th wireless access point will return to default settings. You must re secure you wireless after re set.

That IP is internal only, and has no effect on anybody but you and your router. Local Network means same internal network, and not connecting via the cloud (out there in the internet). Instead, set up virtual server session under advance settings in the routers web interface. This will allow access through the routers firewall.You will have to do some fine tuning since I am not familiar with the games LAN access requirements.