Elna Quilter's Dream 6003Q - Page 9 - Answered Questions & Fixed issues

Elna and Janome both do a 4000 model. Take a look at the link for Elna. It is country specific and doesn't appear to be a US model. https://new.elna.com/us/en/support/support-previous/ Janome Memory Craft 4000 https://www.janome.com/siteassets/support/manuals/retired/computer/inst-book-mc4000.pdf https://www.google.com/search?q=elna+stitch+craft+4000+manual .

The foot controller was pressed (or the start/stop button was pressed if the foot controller is not connected) and the reverse/reinforcement stitch button was pressed while the presser foot is raised. Lower the presser foot lever before continuing the operation

Try this; https://youtu.be/bhqpWuE_Yw4 Hope this tip helps.

Try this site; https://www.mymanuals.net/registration?gclid=EAIaIQobChMIgLTM4pT_8AIVxJTVCh3C9Q69EAAYASAAEgLCSPD_BwE Hope this tip helps.

Check thread sensor. Thread may not click into it.

This is the only Elna Carina available https://www.manualslib.com/manual/879568/Elna-Carina.html#manual https://www.google.com/search?q=elna+carina+tsp%2C+type+56+manual ..

of course it could be . I have replaced a couple on my machines

you need the manual! https://www.google.com/search?q=PRO+900+DCX+manual ..

YOU DID NOT HAVE IT TIGHT ENOUGH ME THINKS

You may find the capacitor that is fitted to reduce TV interference has failed. It's the grey one in your photo.

Parts suppliers in the last link. Is it this part? https://www.sewingpartsonline.com/cam-gear-elna-air-electronic-68-sewing-machine.aspx suppliers https://www.google.com/search?safe=off&rlz=1C1QJDB_enCA643CA644&sxsrf=ALeKk01O0PiPQ5BM1FrWDLlqvJ95Qn7pLg%3A1613434648485&ei=GA8rYIiNHb2s5NoP8oW0mAY&q=elna+carina+sewing+machine+parts ..

Request the service manual from Elna.

https://www.manualslib.com/manual/871002/Elna-Excellence-730.html?page=92#manual

try less down pressure to the foot

So your sewing machine starts and stops sewing, like it loses power: Sounds like intermittent power, which indicates an intermittent short circuit. This may be by a wire, contact point or a terminal being dirty, burnt, worn, loose or bent out of place somewhere. Sometimes you can locate it by: 1. Visual inspection of every contact point from Plug to Motor. 2. Physically jiggling the power line ( while the motor is running, inch by inch, from the wall plug to the motor. 3. Key places to check first: (A) Any place a wire bends, (B) Any place there is a Contact Point (that means (a) Inspecting the wall plug, (b) the wire, (c) where it goes into the machine,(d) Where the power feeds the lines inside the machin, (e) Inside of the Foot Controller: Look for sparks or burnt marks; then Clean and Check all wires and contacts points in and to and from the Controller. 4. Replace any bad, weak or over-aged wires. 5. If you cannot find the fault these ways, buy a $10 buck Non-contact voltage detecter from any hardware store or Electrical parts supplier, and read the directions. 6. The sewing machine must be on, but not necessarily running (at least at first). 7. Now hold down the button on the detector as you scan along the power line from plug to motor. 8. If the detector Blinks and Beeps when it should not, or does not Beep and Blink when it should, that is the point where the problem is. 9. If you stil cannot locate the intermittent short, replace all or part of the power feed cords until it is fixed. 10. You can order complete replacement power cords for your machine from a Sewing Machine parts supplier, or you can fashion some of it from a brand-new 16 Foot extension cord. Good luck, some shorts are tough to locate when they are intermittent. It is easier to find if it goes out totally. Hope this helps you fix your electrical short. Amender, 2020-12-03#

IBOUGHT A SIMPLE BOBBIN EINDER ONLINE SO I DID NOT HAVE TO UNTHREAD MY MCHINE TO HVE A BOBBIN READY AHEAD OF WHEN IT WAS NEEDED .https://www.walmart.com/ip/Simplicity-Bobbin-Sidewinder-1-Each/10098033?wmlspartner=wlpa&selectedSellerId=0&wl13=3840&&adid=22222222227000002625&wl0=&wl1=g&wl2=c&wl3=361203706788&wl4=pla-363070564922&wl5=9015985&wl6=&wl7=&wl8=&wl9=pla&wl10=8175035&wl11=local&wl12=10098033&veh=sem&gclid=EAIaIQobChMItIi_sYH17AIVgeKzCh2DnQ3XEAQYASABEgI5yfD_BwE

You could looking it up on google and check the companies official website too.

Me also want to try this.

Posssible free manual found using https://www.google.com https://www.manualslib.com/manual/641401/Elna-Elna-Lock-L4.html?page=5#manual Other manuals appear in search results for sale.

https://www.youtube.com/watch?v=ZDUizG3s9tM https://www.pinterest.com/pin/568931365427426825/