Top 20 Husqvarna Designer I Questions & Answers

Question edited for clarity. Question moved from Cars and Trucks. There is not much on this, and you will probably need dealer service and cleaning. https://www.google.com/search?q=Husqvarna+Designer+Jade+35%2C+says+needs+to+rest ..

You might be lost without the "security dongle" many softwares for digitizing require one specific to the mfg, and series version. Scour the sewing areas and all the sewing thread kits at Grandmas! Cheers, Embroidery Services San Diego, CA

Try submitting your question to the correct category.

It sounds like the design was created using a larger hoop size. You can select different hoop sizes in your setting see attached pic

Search the internet for: Make + Model + the word "Manual" or contact manufacturer support. ..

Unless you can figure out how to tighten it, you'll probably need to take it for service.

VIKING QUILT DESIGNER II USER MANUAL Pdf Download.

www.manualslib.com > ... > Sewing Machine > Quilt Designer II View and Download Viking Quilt Designer II user manual online. Quilt Designer IISewing Machine pdf manual download.

Viking Husquavarna Designer II Sewing Machine - YouTube

? 1:27 www.youtube.com/watch?v=k0mXebnmzT4 May 30, 2008 - Uploaded by proudpop9pj Here you can view my Viking Designer II Sewing Machine at work. The first two times I used the foot pedal, the ...

Check the manual - are you using the settings recommended for the s foot? Are you using the proper thread? How about the tension 0 is it properly set for the size and thickness of thread being used?

Get a service manual from a source such as sewusa.com I've never seen a schematic. The power source (12v) for the bulbs is from the main circuit board mounted behind the front cover so you have to disassemble all the covers to get to it. If the problem is more than burned out bulbs or the cable connection I suggest consideration of an external LED light rather than trying to troubleshoot the circuit board. See www.bendablebrightlight.com for one such light.

take your machine to a Viking dealer and have them check it out. it probably has a worn 8 button keypad. the reverse button is usually the first to wear out. this not a DIY project.

Need more information Audrey. If you are trying to use Windows XP, Windows 7 software on Windows 8??? without updates to both- That would be your culprit. Cheers, Kelly Embroidery Services San Diego, CA

Try E-bay, Craig's List, Amazon....etc....

Probably the Thread Out sensor is too sensitive. We just disconnected it on several of our machines. Not necessary as you're watching the machine 99% of the time when you're using it. Bill in Oregon

First try a couple of different disks to make sure the disk itself is not corrupt. If this does not solve your problem then unfortunately the disk drive will have to be replaced. A new one may no longer be available but many Des. 1 owners have upgraded to USB, (which you should also consider doing) so some workshops may be able to supply you with a 2nd hand one.

Check bobbin case for loose threads in spring area that could be causing bobbin not to hold enough tension on bobbin thread. You can check bobbin case tension by using your needle plate. Holding bobbin case in your hand, insert a bobbin and thread it through the spring as usual. On the end of the bobbin thread, tie your needle plate to the thread. Hold case in your hand side ways so that thread travels downward with needle plate and thread trails downward across the case. The case should be perpendicular to the table top or floor. The weight of the needle plate should be so that the thread does not travel down unless the bobbin case is shaken slightly. The thread should then travel down slowly but stop once you hold case steady. If this is ok, check top tension. Turn on the machine. Lower the presser foot. With needle threaded, pull the thread the needle. You should feel some resistance. If there is none. Raise the presser foot and brush out any loose threads that might be caught in the upper tension disks. Many times, loose threads can get caught here that will keep disks from closing completely. Hope this helps. Good luck.

Do you have a older computer. Probably yes is the answer. How did previous owner operate. Call manufacturer.

The stick will show up as a drive letter. Switch to that drive letter and then highlite all the files on the CD drive Click copy. Change to the drive letter of the stick and then paste the files onto the stick.

Replacing the spool holder requires removal of the front cover (which basically requires removing all covers). Unless you're an avid do-it-yourselfer, you would be better off having it done. While it's not a complicated job, you have to do it with great care so as not to damage wiring harnesses, gaskets, etc. If you tackle the job, get a service manual and make sure you have the necessary tools. You most likely will have to get a replacement spool holder beforehand.

i am sure you can go to manufacturer on line and download a user manual free