20 Most Recent Juki MO-655 Mechanical Sewing Machine - Page 5 Questions & Answers

Try a brand new needle. If that doesn't work, most likely the machine is out of time. ...

The broken needle may be jammed in the hook or race and/or the hook or race may be damaged. Remove the bobbin and the hook. See video on removing hook on a Juki.https://youtu.be/GqWBdQ4bLrk

Question edited for clarity, spelling and capitalization. Question moved from category 'Cars and Trucks', to Juki sewing machine. When was the machine last serviced? They should be serviced every 2 or 3 years. Most people never service until they fail and then wonder why they failed. Slow, weak sewing would be caused by the foot pedal having dirty contacts n the insides. It has a wire wound track and a contact terminal. The fact the needle doesn't go up and down is either caused by it being in bobbin winding mode, or a link has come off inside. So first thing to do is open up the foot pedal and clean the contacts with electrical switch cleaner (NOT WD40). Then check you aren't in Bobbin winding mode, normally a clutch on the hand wheel. Or Take it to Juki Service. Videos and the Service Manual in the link https://www.google.com/search?q=Juki+HZL+29+Service ..

Sewing machines can make clicking noises, but as yours is new, I would take it to the seller and ask them to check it.

hello regarding error code E808 mostly happened in SC-920 control: 1- check +33 DC volt output for thread trimmer - bac-ktack- presser foot lifter. 2- check CTL board. ( any electronic components damage ) the most reason for E808 coming from CTL board. best regards ASHRAF ABOZID [email protected] Cairo - Egypt

Is there excessive oil on the needle shaft (above the screw)?

Try lowering presser foot and advance hand wheel so needle is at its lowest position. Then take a clean dry rag and wipe around the shaft just above the screw and see it gets dirty. If yes, the machine needs a thorough clean and lube.

'Over-Current' error. https://www.manualslib.com/manual/1579619/Juki-Ddl-8000a.html?page=68 ..

PERHAPS YOU NEED A NEW BELT

sadly only a person that can see it can help . we have no crystal ball here

open eyes and look at the screw

then take it back to where you bought it let them make it right we can not fix it as it has a warranty

Page 42 of the Service Manual shows both Errors 25 and 26. Talking of Errors, I fixed all the errors in the question to British English :>)

ENGINEER'S MANUAL - Superior Sewing Machine & Supply ...

www.supsew.com > download > Juki > Juki SC1

PDF mJUKI. 3C-1. SC-2. CP-30 'CP-ISO. CP-230'CP-330. ENGINEER'S MANUAL. 4-. 1.. caoo <r £• ... 24. 14) Number of revolutions at low speed. 25. 15) Number of revolutions for thread trimming. 25 ... 26) Needlebar up/down position retaining function. 32 ... EXPLANATION OF ERRORS AND CORRECTIVEMEASURES. 38. 6.

HZL or HZD?

HZL-L series - JUKI

https://www.juki.co.jp > HZL-L Series_EN_inst

PDF Keep this manual accessible so that you may refer to it at anytime while operating the machine. INSTRUCTION MANUAL. COMPUTER SEWING MACHINE. ..

Looking for manual for Baby Blindstitch CM-606 S/L M079212 Email: [email protected]

The tension on the belt is probably too tight. This would keep the motor from turning the machine or it would turn it with a lot of resistance. Loosen the belt tension.

Remove the needle is possible. Force it in the normal direction of travel with the handwheel. You can't break it. This tip from a dry cleaners that does repairs and has 6 machines. Then run the machine full speed with no needle for about 20 seconds. I removed your duplicate post. When you submit a question, you have to press Refresh to see it.

Contact Juki direct, it is their machine. The dealer is a seller licensed by them. They will make the right things happen. https://www.jukihome.com/products/sewing/hzl-dx7.html Click Support, message or phone.

https://www.manualslib.com/manual/814520/Juki-Dnu-1541.html https://youtu.be/aaNsmgHQzTo

CHECK WITH LOCAL DEALER OR GOOGLE IT