20 Most Recent Copystar CS-1620 Copier - Page 5 Questions & Answers

Sounds like you have a faulty thermistor. (heat sensing device) The 6020 indicates an abnormally HIGH temperature. If the readings are greatly different in the two thermistiors or one is not touching the hot roller could also be the problem.

Hi amanda_blevi,

I would like to clarify if what is the brand and model name of your unit?

Thank you for using FixYa.

update the latest firmware and the problem will be solved

Have you seen this answer ? http://www.fixya.com/support/t2532905-get_scanner_work_just_set_up

check for jam in the exit unit of the copier.if there is no paper in there then the exit unit sensor is either dirty or not getting back to original position.check it if ur a rep or call one

You probably have it by now, but I'm looking too. I did come across this site in the U.K. that will sell it for 5 British Pounds (about $8 right now):

http://www.starmount.co.uk/products/343.html

The latest version is 1.86 (Build 1009).

The only downside is that they appear to not take credit cards unless you're in the U.K. to start with -- you need to do a bank transfer of some kind.

The new ink cartridge has a plastic lining requiring removable before snapping in placement area on printer. Inserting a new cartridge without removing the plastic lining safe requirimng disposal would least produce results upon installing cartidges. Good lcuk

This error is associated with the optical section. check if the rail is dry and lubricate it.

The waste toner container is full. replace waste tone container with a new one

You might have touched the main charger cleaner a green part above the waste toner container. just push it inside and try to copy and print

replace the transfer assembly

perform Sim 163

replace corona wire or what type your machine??

Click on the link below and contact Kyocera, the makers of the Royal copystar 4000D copier and they will provide you with the seven digit code to get your machine up and running again, click on the link below:
http://usa.copystar.com/americas/jsp/Kyocera/supportwiz.jsp

it stands for add powder (toner)

Hi

Thanks for using FixYa. Error Code E07 means paper jams near the fuser unit. Try removing the paper jams and check for any small bits of paper near the fuser unit.
Follow this procedure---

1. Open the multi-bypass.
2. Open the left cover. Holding the green handles, lower the two fixing section release levers.
3. Remove the misfed paper while taking care not to tear it. If the paper is not easy to remove, proceed to the next step.
4. If the paper is removed successfully, proceed to step 9. If the paper should be torn, remove all the scraps from the inside the copier.
5. Holding the green handle, open the ejection guide.
6. Remove the misfed paper while taking care not to tear it.
7. Close the ejection guide.
8. Lift the fixing section release levers.

NOTE--If the fixing section release levers are lowered, the left cover does not close.
9. Close the left cover and multi-bypass.
10. Pull the drawer out and check that no paper is misfed.
11. Close the drawer slowly.

Also check for the User and Operating instructions manual for details--
Copystar C1810 User and Operating instructions manual

Please do accept the solution if the issue is resolved or else revert for further assistance.

Thanks
Rylee

four things that cause lines on copiers dirty optics needs drum or drum blade or corona in a lot of the copystars the drum drumblade and corona are all in one unit that you can replace

please go to here. http://usa.copystar.com/americas/jsp/Kyocera/download_center.jsp?pid=13316&pcat=10569&rcid=10009&rscid=10028

C6000, С6030 is Abnormally high temperature in the fixing section – The fixing unit thermistor output voltage remains less than 0.5 V for longer than 1 s, indicating the fixing temperature rises above 536F this may be the fuser is no good. Sorry? coll to Servise center Mita. Dood lack!

What type of paper are you telling the copier your using, your copier's duplexer (The section that turns the paper over for the second side image) if the copier is told that the paper is to thick (lbs/gm2) you operator manual will tell you what media (paper) can be used. either, via lbs system (US System) or g/m2 system rest of the world. What the paper comes wrap up in will tell the thicknest of the paper either in lbs, g/m2, or both Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f