20 Most Recent
Konica Minolta DiALTA Di200 Copier - Page 7 Questions & Answers
Error cod sc32-04
There is no SC3204 or C3204 code on the Minolta Di200. I would either need the correct code or the correct model of Minolta you have. Please provide better information so I may assist you further.Thank You for using Fixya.
Hi.. please help me.. my minolta dialta 183 is not
C0500: Warm-up failureStep 1Check:Fusing Heater Lamp (H1) turnsON.Step 2Check:Fusing Heater Lamp (H1) is open-circuited.<Check Procedure>Check the resistance across bothends of the Fusing Heater Lamp(H1).The Fusing Heater Lamp is open-circuitedif the resistance is infinity.Result: YESAction: Change Fusing Heater Lamp (H1).Step 3Check: Thermoswitch 1 (TS1) is operational.<Check Procedure>Check the resistance across bothends of the Thermoswitch 1 (TS1).The Thermoswitch 1 is open-circuitedif the resistance is infinity.Result: NOAction: Change Thermoswitch 1 (TS1).Step 4Check: Fusing Unit Interlock Switch (S2) isoperational.<Check Procedure>Check continuity across terminalswhen the Fusing Unit InterlockSwitch (S2) is turned ON.• Across S2-1A and S2-1B• Across S2-2A and S2-2BResult: NO Action: Change Fusing Unit InterlockSwitch (S2).Result : YES Action: Change DC Power Supply (PU1).Step 5Check: Thermistor (TH1) is open-circuited.<Check Procedure>Check the resistance across CN15-2and CN15-3 on the Fusing Unit sidewith CN15 disconnected.The Thermistor is open-circuited ifthe resistance is infinity.Result: YESAction: Change Thermistor (TH1).Step 6Check: The following voltages are suppliedfrom the Master Board (copier: PWBA).<Check Procedure>Check voltage across a Master Board(copier: PWB-A) pin and GND whenthe Power Switch is turned ON.• Voltage across PJ10A-7 and GNDDC24 V when Fusing Heater Lamp(H1) is OFFDC0 V when Fusing Heater Lamp(H1) is ON• Voltage across PJ10A-10 andGNDDC24 V when Fusing Heater Lamp(H1) is OFFDC0 V when Fusing Heater Lamp(H1) is ONResult: NOAction: Change Master Board (copier:PWB-A).
Error code c1300
If the problem persists, check wiring between PCs UN3, unit PH, and
the PWB-A and, if correct, change UN3, PH Unit, or PWB-A, in this
order.
Error c0500 reset
your code is a fusing code : fusing lamp broken, thermistor , thermofuse...
For reset the code : you have a little hole on the right of the panel board, introduce a little spin into the hole, enter 3 on the pannel, and reset trouble
KONICA MINOLTA ERROR CODE CALL
Problem with toner bottle motor
After a reset problem, remove the bottom cover back and PC11 toner sensor block cover. And release the locking lever bottle, turn the bottle 1 / 2 turn recontact PC11. The bottle turns she released the lever?
The toner cartridge was replaced
check the toner detector switch it is found just at the toner mounting bracket once you insert the toner a motor should activate to lock the toner in placed.Once the toner is locked the detector switch is triggered by the toners cover and sends a message to the system that the toner is in placed...clean the switch or replace it if brocken..
Minolta Di 351 code C0500 & need reset code for this
look for a small hole...on right side of the disply panel...THE HOLE IS SMALL THE SIZE OF PAPER CLIP IN DIMETER..IN FACT THE ONLY WAY TO ACCESS IS BY PAPER CLIP.PRESS IT ONCE VERY GENTLY..AND WAIT FOR A SMALL DOT TO APEAR ON THE LEFT SIDE OF THE SCREEN IN THE CENTER.ONCE YOU SEE IT>>PRESS # 3 than you will be promted by a screen to reset troublr code press it to conform MACHINE WILL RECYCLE
HOPE THAT HELP S
GOOD LUCK
My minolta dialta copier has
COF24 is an AIDC code. The AIDC sensor is under the drum and is likely dirty. Remove drum unit, remove drum and wipe sensor. If there is a pile of toner you will probably have to replace the anti-spill blade
Can I get the procedure
You
remove the back cover, I believe it is 4 phillips screws.
Then you will see the fuser unit. There are 4 more phillips screws to
remove and a couple of connectors to unplug. Then pull the fuser back
and out and replace.
I current have a konica
Hi one thing you can try is turn oiff the machine hold down the utility key switch turn back on the machine keeping the utility button pressed down after 20 seconds release the utility key on the display it will come come up with trouble reset on the screen touch this on the screen and the machine will reset the error code leave the finisher detached from the machine
in regards to the finisher you will need a certified engineer to look at this temp you can put a box between the finisher and the machine to catch the paper
Not finding what you are looking for?