20 Most Recent GE Profile Performance WPSF4170WAA - Page 8 Questions & Answers

There's a part under the agitator that lifts off if you pull up from the bottom on both sides) called a coupler that is attached to the shaft with one bolt. The plastic teeth probably have stripped off from this coupler, causing the agitator to not agitate properly.I would buy the part on amazon.Here's the link to the exact part:shorturl.at/oxDX0Video to show how:https://youtu.be/PN4Q-VqyReo

First make sure someone didn't turn off the supply valves where the washer hoses are attached to. If both are on, then try to fill machine and switch between hot and cold water. If one of the 2 temps works, the other half of the fill valve is bad. The fill valve is the part where the hoses attach to the back of the machine. It is a 2 part electric valve with 2 electric coils on the valve. Could be one coil is bad or possibly the filter screen is blocked on one side. Screens can be checked and looked at by removing hoses and looking inside end of valve. If coil is bad, complete valve needs replaced. Easy exchange, a few screws, 4 wires, and a small hose leading to inside of machine.

Owner's Manual https://products.geappliances.com/MarketingObjectRetrieval/Dispatcher?RequestType=PDF&Name=49-90315-2.pdf

Door Switch or a fuse is bad.

Timer may be shot..

E43 is for "excessive drive system brake time"

Reset with
1) unplug 3 seconds,
2) hold Power & Start to display "Jr",
3) cycle thru using the Custom 2 button (3 times) to display E43,
4) hold Power & Start to clear code to E00,
5) stop.

https://products.geappliances.com/appliance/gea-support-search-content?contentId=17391

Try rebooting the dishwasher. Turn off the circuit breaker for 2 minutes. It will reboot when power is restored. If it's still blinking and beeping, you may need service.

Is the hot water inlet solenoid valve working?

Faulty diverter valve

You can google your question for answers About 28,000 results (0.62 seconds) https://www.hunker.com/13410540/how-to-reset-a-ge-washing-machine

Put it back on and see what happens. Nothing to loose

Can you pull it out?

The timer has failed. Never had much luck fixing them but replacement is easy... if you can find one

If it's atill under warranty, use it! Call their customer service and tell them what's going on, I bet it's under warranty still and if not they're still extremely likely to help you out! But it sounds like it's overheating and cutting off, by it I mean the motor that turns the drum that your clothes/water/etc. are in. When these electric motors overheat they'll turn off automatically as a safety precaution as to avoid damaging the motor permanently. Once it shuts off, sometimes they'll come back on and work for a while and then just overheat again- it's a vicious "cycle"! Sorry for the corny humor but I couldn't resist. This is common amongst other things like vehicles(fuel pumps & ignition modules are famous for this), many electronics including an iPhone shuts down when overheated until it's cooled down enough to operate safely but it'll overheat again- it's a part failing but holding on for dear life and it's fate is certain. It's possible this could be a simple sensor, call the experts at GE Customer Suppourt, they'll help you troubleshot the issue and get it resolved once and for all, best of luck!

You can go online to searspartsdirect.com and enter your model #. You should be able to find part description, price and part #. Google part #. Should be able to find pretty cheap

Hello ! Possibly, the transmission belt under the dish grill fell.

there could be a fuse in the control board that you can look at other than that get in a technician as the unit could be damaged from the power surge

http://www.appliance-repair-it.com/frontload_washer.html https://products.geappliances.com/appliance/gea-support-search-content?contentId=17391

It may be a cracked drain hose behind the drain/ clean out cap or a loose clamp. i had the same issue and fixed this myself in less than 20 minutes. I also removed the drain cap and found missing laundry items and a few other items blocking the system. If you have not googled or checked you model online you can find out the location of this cap, which is normally behind the bottom front plate on your washing machine. Generaly on the right side.