20 Most Recent
GE Profile Performance WPSF4170WAA - Page 3 Questions & Answers
My tub will not spin on my GE washer and there is a red flashing light on the circuit board
The red flashing light on the circuit board of a GE washer is often an indication of an error code or fault. The error code can help diagnose the issue. Here are some common causes of a GE washer not spinning and a red flashing light on the circuit board:
- Door lock error: Ensure the door is securely closed and latched.
- Drive belt issues: Check if the drive belt is broken, stretched, or has come off the pulley.
- Motor issues: The motor may have failed or the wiring may have come loose.
- Central control unit (CCU) issues: The CCU may have failed and will need to be replaced.
If you are unable to diagnose the issue, it is recommended to have a professional technician diagnose and repair the problem as it may require technical skills and specialized tools.
GE 465 top load washer corrugated drain hose was wet feeling about half way up and water all over floor after washing.
It sounds like there may be an issue with the drain hose on your GE 465 top-load washer. The fact that the drain hose is wet halfway up suggests that there may be a leak in the hose. This could be caused by a hairline crack or a problem with the connection between the hose and the drain outlet.
One possibility is that the extra rinse option and the maximum water level setting on the tub caused a higher volume of water to be drained through the hose, which may have caused an existing issue with the hose to become more pronounced.
Another possibility is that the internal drain pump is not functioning properly and the water is not being pumped out of the machine properly, causing the overflow.
It is recommended to contact the manufacturer's customer service or a professional technician to have the washer inspected and repaired. They can check the hose and connections, and also the drain pump to determine the cause of the problem and fix it accordingly.
It's important to keep in mind that attempting to repair a washer can be dangerous if you're not familiar with the proper procedures and safety precautions. It's best to let a professional technician handle the repair.
Regenerate response
GE washer inlet stripped, cross threaded
If the inlet on your GE washer has been stripped or cross-threaded, it may be necessary to replace the inlet to repair the problem.
To replace the inlet on your GE washer, you will need to follow these steps:
- Disconnect the power to the washer by unplugging it from the wall outlet or turning off the circuit breaker that supplies power to the washer.
- Shut off the water supply to the washer.
- Remove the hoses from the inlet by loosening the hose clamps or fittings that secure them to the inlet.
- Remove the screws or bolts that secure the inlet to the washer.
- Carefully lift the inlet out of the washer and set it aside.
- Install the new inlet by reversing the above steps. Make sure to connect the hoses to the correct fittings on the new inlet.
- Turn the water supply back on and check for any leaks.
- Restore power to the washer by plugging it back into the wall outlet or turning the circuit breaker back on.
- Test the washer to make sure it is filling properly with the new inlet.
Note: These instructions are general guidelines and may vary depending on the specific model of your GE washer. If you are unsure of how to replace the inlet on your washer, it is recommended that you contact a qualified appliance repair technician for assistance.
I have a GE washing machine fairly new 2020.door lock went bad replaced it still don't 'work . Ran all the tests and even the door still doesn't lock . What's my problem?
If you have replaced the door lock on your GE washing machine and it is still not working properly, there could be a few different causes for the issue. Here are a few things you can try:
- Make sure the door lock is properly installed and aligned with the latch on the door.
- Check the wiring between the door lock and the control board to make sure all connections are secure and there are no damaged wires.
- Test the door lock with a multimeter to see if it is receiving power and functioning properly.
- If the door lock is receiving power and functioning properly, the issue may be with the control board or another component in the washing machine. In this case, it may be necessary to take the washing machine to a repair shop or contact the manufacturer for further assistance.
It is also a good idea to make sure that the door lock is not being activated by any foreign objects or debris that may be preventing it from functioning properly.
GE front loader spins slow
need the Model number to help you find the white tag and add the model number it inside the front door frame
Not finding what you are looking for?