20 Most Recent GE WJRR4170E Top Load Washer - Page 4 Questions & Answers

sounds like a belt problem. if you're not smelling burning rubber (belt) either the belt has come loose or broke

HI to help you with this problem you need to have a look at the prsure switch inside the appliance its a round thing with a plastic tube or rubber that go's under it try to replace that first and that should sovle your problem let me no how it go's noffie.....

could be the clutch assembly on the motor.

sounds like a dead animal in there

if it is a top loading unit you will need to replace the motor couplor. you can take of the pump (leave it conected to the hoses or you will ahve a big mess). disconect the wiring harness from the motor and take the motor off. motor couplor consists of two three prong peoces with a rubber ring conecting them. There is a new one on the market that has a metal sleeve in it. makes it stronger. post the model# and I can post a part number for you. or you can just order it from sears parts. not sure on the number to call in the states (im in canada) but the same numbeer you would call for service can look after sending you the part. good luck and for safty please unplug the washer before you work on it.

check the lid switch and striker

your outlet hose put it down close to the floor into a bucket if water comes out then your pump may have blown if not it will be blocked up u may find if u take the outlet hose of water may come out which means your pipe is blocked

your pump is on its way out inside they have a small fan which pushers the water out if that is lose than the pump has to be replaced common fault

It sounds like the clutch is slipping https://www.google.com/search?q=GE+WSLP1100A0WW+not+agitating

Top Load Washer - Fills But Will Not Agitate

GE Appliances https://products.geappliances.com > appliance > gea-sup... If the lid switch probe or magnet is missing or damaged, the washer will not agitate or spin, even with the lid closed. Missing: WSLP1100A0WW ‎' Show results with: WSLP1100A0WW

SOLVED: GE WSLP1100A0WW not agitating

Fixya https://www.fixya.com > ... > Washing Machines > GE 17 hours ago - Ge top loader washer agitator does not work To check the agitator. Start the washer into wash cycle. Once started Push down on top of agitator.

Ge Washing Machine - Washer Won't Spin Or Agitate

Repair Clinic https://www.repairclinic.com > RepairHelp > Ge-Washe... If a washer is not spinning or agitating, you should first determine if the drive motor is running and if power is reaching the drive motor. If no power if ... ..

No there’s no brushes for GE handmixer

Hello Heather Good to see you again. Also check the small strainers on the water connectors. They can block up with limescale and debris. While the connectors are off, turn on the water into a bucket or a sink. You should have a VERY powerful jet of water. Anything that will reduce flow will lengthen the fill time and therefore to total wash time due to fill and rinses. When it pumps out, also check you have good flow in the drain hose and items can jam in the ridges and catch lint enough to block them almost completely. One clever thing to do is whilst the water inlet connectors are off, unlock the drain hose, unhook the part that makes the hook, put the round connector in the hose and wrap a tea towel around it. Get someone to turn the water on full bore whilst you are gripping the two hoses together. Run it for a full minute. Water will be flushed into the machine through the pump in reverse. Put everything back and run a rinse and spin with nothing in it, look at all the black lint that is pumped out! I did that once at work and found an apple stalk that had lodged across the ridges of the drain hose which had 90% blocked the pipe. ..

If your inlet valve itself is stripped then you have to replace the valve. The plastic thread is part of the inlet valve. If its only the screen in your inlet valve you can remove the screen and replace it. However if you crossthread anything plastic it HAS to be replaced.

If you give me your model number of the washer usually the wpl 4318046 can be used as an inlet valve which is a cheaper alternative than your local parts distributor would tell you. GE parts on avg are 30% more expensive than anything else. On ANY ge appliance there is usually a way around there replacements with some minor altercations. I wish this site had a way you could contact me directly. I just joined so am not an expert yet but ive done my time in the field. If i could give you any expert advise its DONT BUY GE, OR LG.

Let me know if this helps.

Question edited for clarity 'MAKE model (WHAT IT IS)'. You posted to Televisions, moved to GE Washing Machine. It may be the lid lock, test it with your digital multimeter. Look for loose or damaged connections. https://www.google.com/search?q=GE+Gtw330ask0ww+not+running ..

check under agitator possible worn cogs

check voltage to pump if ok bad pump also check drain hose

Check the water level sensor.

Just remove the drain hose from the drain upstand pipe and lower it to the floor. It will empty the pump or water.You can also drop a pint of car anti freeze into the machine just to be sure if you wish.

You likely have a water leak spraying onto electrics, or the water inlet valve is shorting out.

Remove the bottom impeller and clean out the water proof grease that has come out of the seal and drive shaft.

I understand your frustration. It sounds like your GE washing machine is having some problems. Resetting the washer may help to fix the issue. Here are the steps on how to reset a GE washing machine WPDH8900J1WW: 1. Unplug the washer from the power outlet. 2. Wait for 2 minutes. 3. Plug the washer back in. 4. Turn on the washer. 5. Select a cycle and press the start button. If the washer still does not work, you can try resetting the drum motor. To do this, follow these steps: 1. Unplug the washer from the power outlet. 2. Wait for 1 minute. 3. Plug the washer back in. 4. Open and close the lid of the washer 6 times within 12 seconds. 5. Close the lid and press the start button. If the washer still does not work after resetting the drum motor, you may need to contact a qualified appliance repair technician. Here are some other things you can try before resetting the washer: * Make sure that the washer is properly leveled. * Check the water supply hoses for leaks. * Clean the lint trap. * Check the detergent dispenser for clogs. I hope this helps!