Top 20
Gestetner DSm745 Black and White Copier Questions & Answers
Sc 542
enter service mode then mode then reset/clear sc if it came back than change the thermistors
Service mode enter ricoh aficio
press th orange key, say three times.
press 107 with the keys.
press and old the clear or cancel or stop key for about four seconds.
the ma chine will naw take yu to the sp mode.
The copy is light, who can i fix it
kindly check if there is enouh developer in the unit .if there is check the glass covering the laser unit and clean it.
if there there is no developer then change it and the problem is solved
What does service code sc350 mean?
SC350:
Problem:
ID sensor pattern test error
Description:
One of the following ID sensor output voltages was detected twice consecutively when checking the ID sensor pattern.
1) Vsp ? 2.5V
2) Vsg ? 2.5V
3) Vsp = 0V
4) Vsg = 0V
Possible Problems:
• ID sensor defective
• ID sensor connector defective
• Poor ID sensor connector connection
• I/O board (IOB) defective
• High voltage supply board defective
• ID sensor dirty
• Defect at ID sensor pattern writing area of the drum
** Generally, I've found this problem to almost always be one of the last two items listed above.
Witch is better Gestetner DSm745 or richo 1045 or
dsm 745 has more modification than1045 more comfortable less disputes little problem. technicians can see this difference there are more details but i expressed that dsm 745 is recently than 1045 good luck
Quando ligo a maquina dsm715
Independente do modelo ser Dsm715 ou Dsm745 esse codigo corresponde a um erro na Unidade de Laser, mais precisamente com o sincronismo.
A primeira coisa a verificar nestes casos é se a Unidade de Laser está suja. Por vezes cai toner para o Laser e provoca estes codigos.
Se tiveres conhecimento tecnico saberás chegar á unidade de Laser. Se não tens esse conhecimento aconcelho a não mexeres (chama alguem que o saiba fazer).
Na minha opinião este deve ser o primeiro passo a dar. Deves fazer uma limpeza na Unidade de Laser.
Se não resultar replica para mim ou volta a colocar a questão no Fixya. Existem otros factores que podem provocar este codigo.
Fica bem!
It can not copy well
Let me understand your problem. You are saying that the text is not black in areas on the print, they appear to be white or washed out. If this is the case the first thing that you may try is to remove the "toner shield glass" and clean it. It is located directly under the toner bottle tray, possibly behind a little metal bracket. It just slides out to the front of the machine. If that does not help, then the machine would likely need to have the developer and drum replaced.
How do i password protect our copies?
you can protect your copier with user code protection just fallow theis steps 1. Press the User Tolls Button 2. Tuch the System Settings 3. Tuch the Keyoperator tools 4. Tuch the User code managment 5. make copier ON & tuch OK 6.Tuch Next and Tuch Addressbook Managment 7. Tuch new program 8. Tuch User Code 9. Enter the number your choise & Tuch the # 10. Tuch the function Eg. Copier & Tuch the OK and Exit the user tools - thanks
I have a gestetner DSm745e it keeps on poping out
Charge roller current leak.The polling module detects a current leak of the charge roller.Check,clean or change the charge roller,verify the connection of the PCU,and verify the high voltage suplly board conectors.Turning the main power switch OFF and ON resets the SC code if the error is caused by incorrect sensor detection.
How would I identify faulty fault sensors in gestetner MP2501L copier and replace them?
You can't. As I said you need the service engineer with the laptop. These Office Machines are NOT consumer serviceable. They hook up the laptop with the Ricoh software and it interrogates the computer, the mainboard and everything on it. The error message you get is from the brains inside it..Original question and answerhttps://www.fixya.com/support/t29802178-am_posting_again_stripped_off_gestetner..
Am posting again. I stripped off gestetner MP2501L 8 times due to problem ' see instructions on right side to solve' but same. No paper inside. What is the actual problem.
Hello Christopher
Are you in the Philippines? I notice that your copier has changed from Ricoh to Gestetner? We are a North American website.
This is a commercial office machine, and from my experience of them is that on the right side you will see on the inside, a list of instructions for where to check for obstructions. It seems you have already done this 8 times! Frustrating! Try this;
Open the right side cover, unlatch all the bits at that side.
Open the straight pass door on the left side.
remove ALL the paper drawers.
Get a powerful flashlight, look in all the spaces you have just created, especially at the edges of drawers and paper pathways. You are looking for a tiny piece of paper that one of your employees carelessly left behind after a paper jam.The one I found was right at the back of the straight pass door. When a sensor is covered, it creates that message.
If that fails, Ricoh will have to come and attach their Laptop scan software to it which will tell which sensor is obstructed or has failed.
Gestetner 5308 error code E-24
SC code:E-21 Paper exit timing sensor remains off
E-22 2nd feed timing sensor remains off
E-23 Master eject position sensor remains
E-24 Feed start timing sensor remains off
point to check- Feed start timing sensor
dirty sensor or failed, air line to get dust off my first step.
Not finding what you are looking for?