20 Most Recent
265072 M12000 Self-Recovery Winch - Automotive Truck Parts & Acce - Page 2 Questions & Answers
My python 4103 p remote is not starting my car
There could be a few reasons why your Python 4103P remote won't start your car. It could be that the battery is dead, the key is not inserted correctly, or there could be a problem with the car's ignition system.
If the car was fine last night, it's likely that one of these three things is the issue. If the battery is dead, you'll need to replace it.
If the key is not inserted correctly, make sure that it is fully inserted into the ignition. If there is a problem with the car's ignition system, you'll need to take it to a mechanic to have it fixed.
Passlock II issues for 99 Tahoe
turn key to start position for 10 minutes and it will reset passlock
Or, once you're tired of being stranded for 10 min every 6 weeks or so, try the following:
Here's the "fix" I did for my 99 tahoe. Took the cover off the
steering column, unplugged the sensor from the cylinder *while* the car
was running. it's a 3 wire plug red w/ white, orange w/black and
yellow. From then on, the car will always start and ignore the sensor.
The only negative is the security light stays on. Replacing the BCM only postpones it from happening
again if the problem is the resistance in the ignition lock cylinder. Check out the following links. Good luck.
http://car.justanswer.com/for/ce07-bypass-lock-sensor-1998-chevy-tahoe
http://general-motors.pissedconsumer.com/gm-passlock-ii-system-has-major-inherent-design-flaws-20080502119601.html
Will not start
Hello Richard
try giving the car a boost as when you keep trying to start the car - it drains the battery. If it starts - your battery is weak and needs changing
if it still does not start. it is either electronic problem or fuel problem.
what car do you have? do you notice any gas leak under your car? it could be a fuel pump.
Replace rotors and brake pads
There is a lot of videos on line to replace rotors and brake pads. If you have never did it before. Please leave it to the experts.
With this said, replacing the rotor and brake pads in todays cars are more easier.
1) get the right rotors and pads for your car.
2) Jack up one wheel at a time. Never work while the car is on a jack. Always use a jack stand to put the car on. Ie lower your car onto a jack stand to be safe. Put some plywood under the jack stand to prevent making holes in your driveway.
3) at this point - I will refer you to watch some videos with Chris Fix on how to replace the rotors and pads.
Road angel won't charge / turn on?
Take memory card out, hold the power button for 15 sec to put it on, now do the same putting it off. Put back memory card and turn it on, it should work now. Johan. South Africa
MTR in standby in radar display Jam2300
Hi there's this website something like reliable-store and it is very amazing for manual for repairing servicing anything
someone on fixya recommended it to me and I thank him even today
They have full manuals and it's verrrrry cheap and mine
I got free in offers
3rd time I also had an issue with the file so the girl replaced it in 30 mins
there is one more but i don't remember its name it was 2 years back bitman something link this
Try it out brother
2010 honda crv how to turn oi life light off
- Turn the ignition switch to the ON (II) position.
- Push the Select/Reset knob repeatedly until the engine oil life is displayed.
- Press the Select/Reset knob for about 10 seconds. The information display shows the reset mode initial display as shown.
- select the "OIL LIFE" indicator by turning the select/reset knob. The display begins to blink. Push the same knob to enter the setting.
- The engine oil life and the maintenance item code(s) will begin to blink. Press the Select/Reset knob for another 5 seconds.
- The maintenance item code(s) will disappear, and the engine oil life will reset to "100."
Not finding what you are looking for?