Top 20 GE Profile JGP636 Gas Cooktop Questions & Answers


Sounds like igniter problem. Did some one pull the electrical cord or has a fuse or breaker blown/ Things to check. Your igniter is run by electricity.

GE Profile... | 751 views | 0 helpful votes


WEIGHTS & DIMENSIONS Approximate Shipping Weight 38 lb Cabinet Width 36 in Cutout Dimensions (Width x Depth) (In.) 33-7/8 x 19-1/16 Net Weight 33 lb Overall Depth 21 in Overall Height 3 1/16 in Overall Width 36 in Space Required Below Cooktop 0 7/16 in
  • POWER / RATINGS POWER / RATINGS Burner BTU Ratings (000's/BTU) - LP Gas (1) 9.4; (2) 7.0; (2) 4.0 Burner BTU Ratings (000's/BTU) - Natural Gas (1) 12.0; (2) 9.5; (2) 5.0 Volts/Hertz/Amps 120V; 60Hz; 5A
  • ACCESSORIES ACCESSORIES LP Conversion Kit Included
  • WARRANTY WARRANTY Parts Warranty Limited 1-year entire appliance Labor Warranty Limited 1-year entire appliance
  • GE 36 Built In Gas Cooktop JGP636WEDWW GE Appliances

    GE Profile... | 235 views | 0 helpful votes


    Look to see if coiled gas line is vibrating against back of stove. (Or try pulling stove forward a bit).

    Otherwise, you are probably correct about a transformer. It can be ''defective'' and still work.

    GE Profile... | 914 views | 0 helpful votes


    yes via an exhaust vent to prevent carbon monoxide poisoning.

    GE Profile... | 113 views | 0 helpful votes


    How do I lite a whirlpool electric gas stove?

    GE Profile... | 266 views | 0 helpful votes


    Spark module part no 318 at parts diagram it may be wet and by using a hair dryer or leave it unplug for some days can dry out and stop. If not then the electric contacts are stuck and need a new spark module

    GE Profile... | 1,102 views | 2 helpful votes


    Hi pauliepaul22,

    The ignition switches probably got wet.

    Please follow my below Tip on how to fix it:

    GAS STOVE CLICKING PROBLEM...

    Kind Regards

    JEDEMEYER1

    * If this solution helped you, please accept it

    GE Profile... | 538 views | 0 helpful votes


    There is a switch that slides onto the shaft for each burner. When you turn the knob to a certain area it completes the circuit to the ignitor module. It sounds like you have a shorted switch. Unfortunately with most 'cooktops', these are not easy to get to.

    It's also strange that only 2 are igniting, usually one module runs all the ignitors. When you turn one of the non-problem burners on, does it click when it supposed to and stop when it's supposed to?

    The ignitors running constantly is annoying and may damage the module, but should not be dangerous unless you have other issues, ie., fuel leaks.

    If you have access to basic hand tools and a multimeter I can walk you through the diagnosis.

    GE Profile... | 324 views | 0 helpful votes


    Hi jsjone1945,

    The ignition switches probably got wet.

    Please follow my below Tip on how to fix it:

    GAS STOVE CLICKING PROBLEM...

    Kind Regards

    JEDEMEYER1

    * If this solution helped you, please accept it

    GE Profile... | 235 views | 0 helpful votes


    Buy them for 86 cents a piece at repair clinic.com

    GE Profile... | 206 views | 0 helpful votes


    Hi,
    The lock switch will need to be replaced. Lock switch, the switch has failed and causes the buzzer to run. Not a difficult repair but the top will need to be remover to fix this. This is not advisable to repair if your not knowledgeable with the installation part of this unit.
    Good Luck

    I’m happy to help further over the phone at https://www.6ya.com/expert/gere_bf68e6055dd61249

    GE Profile... | 809 views | 0 helpful votes


    Hi,
    I would clean the electrodes on the burners really good, sometimes they seem not to sense heat from the burner and will not turn off the ignition system. Other times I fond bad grounds to the cooktop or outlet that can cause the same issue. The electrodes since heat from the burners to shut down the inanition system, also with out a good ground this system is impossible to work correctly.

    I hope this helps

    I’m happy to help further over the phone at https://www.6ya.com/expert/gere_bf68e6055dd61249

    GE Profile... | 173 views | 0 helpful votes


    Hi,
    Here is a tip that I wrote to give details about why your cooktop will notspark to light the burners..

    Cooktop Range Stove spark ignition does not work

    heatman101

    GE Profile... | 151 views | 0 helpful votes


    Hi kayandsky,

    I believe your ignition switches have come in to contact with either water or moisture.

    Please read my below Tip on how to fix the problem:

    GAS KITCHEN APPLIANCE CLICKING SOUND...


    If it does not solve your problem, I'd suggest replacing the ignition switches.

    Kind Regards

    JEDEMEYER1

    * If you found this solution helpful, please rate it

    GE Profile... | 141 views | 0 helpful votes


    The igniter switch is located just below the knobs, If you pull the knob off and look in the hole that the shaft comes through, you will see the igniter switch, To replace them you will need to remove the cook top and flip it over and remove the cover section so that you can get to the back of the controls

    GE Profile... | 199 views | 0 helpful votes


    Hi justin willi,

    I believe your ignition switches have come in to contact with either water or moisture.

    Please read my below Tip on how to fix the problem:

    GAS KITCHEN APPLIANCE CLICKING SOUND...


    If it does not solve your problem, I'd suggest replacing the ignition switches.

    Kind Regards

    JEDEMEYER1

    * If you found this solution helpful, please rate it

    GE Profile... | 75 views | 0 helpful votes


    no,its a bad switch on one of the gas valves,they are piggybacked on the gas valve and are supposed to turn on and off as the valve is turned on and off,on has broken and is on all the time even with that valve in the off position,carefully remove each switch from the circuit till it no longer sparks with all the valves in the off position

    GE Profile... | 359 views | 1 helpful votes

    Not finding what you are looking for?
    GE Profile JGP636 Gas Cooktop Logo

    193 questions posted

    Ask a Question

    Usually answered in minutes!

    Top GE Cooktops Experts

    Marvin
    Marvin

    Level 3 Expert

    85223 Answers

    Cindy Wells

    Level 3 Expert

    6073 Answers

    Paul Carew

    Level 3 Expert

    3489 Answers

    Are you a GE Cooktop Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    View Most Popular

    GE Cooktops

    • GE Cooktops

    Most Popular Question

    igniter ge

    • Cooktops
    Loading...