GE JTP45 Electric Double Oven - Answered Questions & Fixed issues

There used to be some grouchy old guy who had a site, I haven't used it for awhile and forgot the name of it, I think this could be it. http://www.appliancerepair.net/index.html, I will keep looking though.

Cover over display has a film that darkens with age. you can cut the film off.

If it has a red button in the middle, push it until it clicks. If no red button, you have to replace the thermal fuse. If you need further help, I’m available over the phone at https://www.6ya.com/expert/jeffrey_634abadf963e31e5

Possibly a tripped thermal fuse. Should be located behind the panel in between the upper and lower ovens. Might have a red reset button on it you can push down. If it clicks and then works again, look for possible cooling fan problems. If you need further help, I’m available over the phone at https://www.6ya.com/expert/jeffrey_634abadf963e31e5

Candy Oven not heating? How to replace a Candy fan oven element This video will show you how to replace fan oven element in your Please remember to subscribe to our YouTube channel for all appliance tutorials a 4 THUMBS rating is appreciated for answering your FREE question. You searched for candy element How to Repair Home Appliances

My oven lights but takes ages to cook food. Also flame goes off if oven door is closed at the beginning of lighting the oven

No, the parts aren't the same. The W2BB model has this code for that same part WB27T10283, while the A2BB model has this code for that part WB27T10292. The parts Look exactly the same in the diagrams, however in my past I have discovered the hard way that connectors and things in the circuitry are often different even if they fit. They're pretty pricey too 250 bucks or so...good luck!

This is a simple repair and you can do it yourself. If your temperature is off, you have a bad temperature control sensor.

Sorry dearestWe in the wilderness are not familiar with that brand, sorryKolbrun

The temperature sensor needs to be checked.It must not working properly. thanks.

f7 is a stuck keypad or overlay all you can do is replace it

Hi

Error code F7 means that an error with the keypad has occurred. Usually it happens due to loose ribbon cable on the keypad or the electronic control assembly itself going bad. To resolve this issue first, disconnect the power to unit and then gain access to the back of the clock assembly (Electronic Range Control/ERC). Now unplug the touch pad ribbon connector from the ERC, it would be a flat wire approx. 1 1/2" to 2" wide and make sure that the cable is not broken and nothing is shorted on the keypad. After this is done insert the cable back and then plug the unit back to check. If the error is still there then the electronic control board should be replaced. Hope this helps...please post back for further assistance.

Daniel

sears parts direct,,,kind of high,,but a sure thing

Open oven door. Flip metal holder down at hinge to lock hinge. Lift door with hinge attached up slightly and off oven. Reverse to re-install door, making sure notch at bottom of hinge is hooked in frame of oven properly.

F2 During BAKE. Control senses oven temperature above 615F-630F If actual over temperature condition occurred: Look for welded relay contacts on bake or broil relays. If this happens, replace oven control (also called clock or ERC).

If no over temperature condition occurred: Look for a high resistance connection or any other cause of high resistance in the oven temperature sensor circuit. Check sensor, sensor harness and sensor harness connection at sensor and oven control. Replace sensor if found defective.

Remember: Oven control (ERC) measures resistance of sensor circuit , not actual oven temperature. F2 During CLEAN . Control senses oven temperature above 915F-930F If actual over temperature condition occurred: Look for welded relay contacts. If this happens, replace oven control (also called clock or ERC).

If no over temperature condition occurred: Look for a high resistance connection or any other cause of high resistance in the oven temperature sensor circuit. Check sensor, sensor harness and sensor harness connection at sensor and oven control. Replace sensor if found defective. Check door lock switches.

Remember: Oven control (ERC) measures resistance of sensor circuit , not actual oven temperature.

need control board

It does sound like a wiring mistake. Check all the connections and the wire colors against the colors on the Tech Sheet wiring diagram (which is normally taped on inside the control panel). Particularly look closely at how the door switch and lock connector is plugged in. You may have reversed the plug.
Best Regards,
Bruce
www.fixyourboard.com

first check the power then if shows to be good replace clock assy

F1 code
This code usually means that there is a problem with the keypanel. Many times, it means the keypanel needs to be replaced

Good luck and please rate 4 thumbs for the free answer

F2 means usually, that the board detected that it's too hot.
You either need a new control board or a temp. sensor.
ge oven repair orange county, ca