GE JKP20 Electric Single Oven - Answered Questions & Fixed issues


think it means lock door . there might be a sliding lever between the cooktop and oven door slide it to the right .

GE JKP20... | Answered on Mar 01, 2015 | 105 views


Others are having problems with this unit. Have the manufacturer support their product and fix it. It should be covered if it is new. Don't delay in hounding them. Time will expire and you will be left with an expensive ordeal.

GE JKP20... | Answered on Nov 02, 2013 | 99 views


unplug for five minutes and it will reset

GE JKP20... | Answered on Nov 19, 2010 | 124 views


you need to get a tech ,you cant correct this

GE JKP20... | Answered on Sep 10, 2010 | 220 views


good day,
hope this link below will solve your problem.

kitchen appliances

GE JKP20... | Answered on Jul 31, 2010 | 250 views


This is usually a keypad stuck key error, usually caused by a bad keypad or sometimes caused by your control board.
F7 usually means a stuck key on the keypad. I've also seen it caused by a greasey buildup on the keypad connector into the control board. Try pressing each button on the keypad followed by cancel. See if the buttons are registering with the control - should get a beep or some function (execpt up/down buttons need a cook or time function enabled first). If one of the buttons seems inoperative it may be stuck, in which case you probably need a new keypad.
Best Regards, Diana

GE JKP20... | Answered on Jun 16, 2010 | 122 views


two diff relays for them replace relay board

GE JKP20... | Answered on May 06, 2010 | 63 views


I just took apart mine and found the same problem. Broil and range work fine but nothing when the bake function is used. I pulled the heating coil and it showed open (infinite resistance). This could well be your problem too. Pull out the drawer on the bottom and you'll see where the coil connects. Pull it and check resistance with an ohm meter. If it shows open, that's probably your problem. It was pretty easy to pull and shouldn't be too tough to reconnect either.

GE JKP20... | Answered on Dec 25, 2009 | 154 views


From the symptons, I would say that the oven elementg has failed, and needs replacing.
Trust this helps you.

GE JKP20... | Answered on Dec 05, 2009 | 81 views


unplug unit,remove 2 screws at rear of oven where element comes thru wall, unscrew terminals,then reverse the procedure and then turn power on

GE JKP20... | Answered on Nov 04, 2009 | 251 views


yes you can kill the power and lock out the box with a pad lock for safety. the panel is attached by screws usually on the bottom of panel. lower and seperate the control panel ribbon from the erc (electronic range control). without removing any other components leave ribbon loose and replace panel. turn power back on. if the beeping does not recur, the control panel probably has a stuck key. if it does resume the erc is faulty

GE JKP20... | Answered on May 17, 2009 | 162 views


I have a GE Spectra stove. The top element over heated and broke in half.

GE JKP20... | Answered on Apr 20, 2009 | 2,916 views


only thing i could say here is replace the control or clock its real name is an eoc electronic oven control now the part is under a five year warrenty but you have to pay labor and use some one that is authorized for ge warrenty work check your owners manuel for second to five year warrenty and go to ge web site to locate servicer in your area http://www.geappliances.com/service_and_support/service/

GE JKP20... | Answered on Jun 05, 2008 | 186 views


it screws off, make sure you replace it with an appliance bulb.

GE JKP20... | Answered on Feb 20, 2008 | 190 views


Hold the stp/clear button in ??

GE JKP20... | Answered on Feb 16, 2009 | 122 views


OPEN THE TOP AND LEARN JUST AS WE DID YEARS AGO

GE Ovens | Answered on Nov 25, 2019 | 57 views


I am unsure whether you are asking for the control itself or the knob or ?
If you google for GE 169152 control part you will get some results, including some manuals. Once you find the part number of the part you are looking for, you can either look for that part online, or you should be able to find a local appliance part supply store/warehouse to get it from. I got a GE genuine temperatire control for my GE range last week from ReliableParts locally.

GE Ovens | Answered on Oct 24, 2019 | 43 views


This means that the Sabbath mode has been enabled. To disable the program, first press and release the Cancel/Off to stop the current programmed bake settings. Then press and hold Settings until Sabbath Mode Off is displayed. See page 14 of the manual for setting the Sabbath mode. The manual is available on the product page: https://www.geapplianceparts.com/store/parts/assembly/C2S995SEL1SS . The current link to the manual is https://products.geappliances.com/MarketingObjectRetrieval/Dispatcher?RequestType=PDF&Name=49-85241.pdf . Most GE oven codes are listed here: https://www.geappliances.ca/en/support/knowledgebase/range-oven-function-error-or-fault-codes . The Sabbath Mode symbol is shown at the bottom of the table.

This mode can be used to set the oven temperature for an extended bake (usually for a low temperature) or a programmed bake. It's used by those who strictly keep the Sabbath but want a hot meal ready when the Sabbath ends.

I hope this helps.

Cindy Wells

GE Ovens | Answered on Oct 06, 2019 | 56 views

Not finding what you are looking for?
GE JKP20 Electric Single Oven Logo

Popular Tags

28 questions posted

Ask a Question

Usually answered in minutes!

Top GE Ovens Experts

William Miller
William Miller

Level 3 Expert

9179 Answers

Ekse

Level 3 Expert

13434 Answers

Marvin
Marvin

Level 3 Expert

85216 Answers

Are you a GE Oven Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...