Top 20 GE Profile JT955 Electric Double Oven Questions & Answers

Bad oven temp sensor. If you know how to do so you can disconnect the power and remove the temp sensor. The two white wires to the sensor, ohm it. it must read ~1080 ohms. If not really close to that at room temp then replace sensor. If you need further help, reach me via phone at https://www.6ya.com/expert/steven_a67ead41eb5fc62a

The first thing to try and do is to just "kill" all power to the unit for a while, at least 2 minutes, to see if we can kick-start the elements. Hopefully it's just a temporary glitch that is preventing them from starting up. Try shutting off the circuit that controls the oven, at your circuit breaker. Just flip it off for a good 2 minutes or more, then flip it on. Try that and then attempt to run the ovens to see if it makes a difference.

Let me know what you find, in the mean time I am researching this further for you, just reply here..

Thanks,
Tim

Hello,

that this code indicate is that there been an over flow of water(liquid substance) in to the pane of the oven.

What you are to do to fix up this problem is first put off the power supply connected to the oven then unscrew the screws from the back with a screw driver,then trace the wire down to the panel then carefully clean up all form of dirt you can fine around the panel then couple it back ,with this the problem is solve
hope this help?

Thank you and thanks for using fixya.

Hi


Thanks for using FixYa. F1 error indicates that the control board (ERC) has gone bad and the electronic range control (ERC) should be replaced to resolve the issue. Please do rate the solution if the issue is resolved or post a comment for further assistance.


Thanks
Rylee

if its an f-7 error code its due to a stuck error code

F7 means a stuck button on the membrane pad. You may have to replace the membrane switch pad

I have an FA code as well. Dont know what it is. Everytime it comes on I clear it and it comes back. Not using oven, just cook top

Never ever use the Self Clean feature. All it exists to do is to keep the makers in a steady stream of sales of spares. The temperature is 800 to 925'F. The parts can't handle it. Try turning off at the breaker overnight to reset.

Why You should Never Run A Self Clean Oven Cycle & A ...

General Appliance Service https://www.generalappliancesvc.com > why-you-should... Jan 29, 2020 - A self-cleaning oven is a feature on many modern ovens that burns off cooking spills and splatters with an extremely high temperature (932 F° or ...

Self-cleaning oven

Wikipedia https://en.wikipedia.org > wiki > Self-cleaning_oven A self-cleaning or pyrolytic oven is an oven which uses high temperature (approximately 932 °F (500 °C)) to burn off leftovers from baking, without the use ... ‎Pyrolytic process · ‎Alternative technologies · ‎Catalytic cleaning

Self-Cleaning Oven: 6 Reasons to Stop Using Feature ...

FIX Appliances CA https://fixappliances.ca > 4-reasons-stop-using-self-cleani... Feb 2, 2024 - Auto-cleaning, also known as "pyrolytic cleaning," operates by heating the interior of the oven up to 500?C. During this process, grease is ... ‎How Self-Cleaning Ovens Work · ‎Major Parts Damage ..

You remove the door and then split the inner and outer parts of the door. clean the glass with Easy Off spray, rinse well, polish and put it back together. The videos should help as they all work to a theme.

How to Clean Oven Glass-Inside, Outside, and In Between!

The Happier Homemaker https://thehappierhomemaker.com > Recipes > Cleaning Aug 24, 2022 - Spray outside glass with vinegar and wipe down with paper towels. · Clean inside of the oven glass with a scouring pad using the "hack" below. ..

The fuse for a GE Profile electric range model JBP79A0B2AA is usually located behind the control panel, near the power cord. You may need to use a putty knife or thin flathead screwdriver to gently pry the control panel away from the wall before accessing the fuse.

My advice is get rid of it. Or test every joint with washing up liquid and water in a spray bottle. This is what a gas explosion can do to your house. Our windows rattled 2 km away! https://www.google.com/search?q=mississauga+Hickory+Drive+gas+explosion ..

Refer to page 40 to 44 (Troubleshooting Tips) of manual L0707187 (searspartsdirect.com)

Cynthia, I've gone thru the manual here.... https://www.searspartsdirect.com/manual/42qc2frzjh-000432/ge-jgb900sel2ss-gas-range-parts And there doesn't appear that the "beeping" can be disabled. You may try contacting them..... MAJOR APPLIANCE QUESTIONS. GE Appliances Answer Center® 1-800-626-2005. Monday-Friday: 8 a.m.-7 p.m. ET. ... Best to you and Good Luck.

If you have already replaced the Hi-Amp Door Switch on your GE Range Oven (Model: PS968SP1SS), but the oven light still will not turn off, there are a few additional steps you can take to troubleshoot the issue:

1. Check the light switch: Ensure that the light switch is functioning properly. It is usually located near the oven door frame or control panel. Press the switch manually to see if the light turns on and off. If it is not working, you may need to replace the light switch.
2. Inspect the light socket: Examine the light socket for any signs of damage or corrosion. If the socket appears to be damaged, you may need to replace it.
3. Verify the wiring connections: Check the wiring connections between the light socket, the Hi-Amp Door Switch, and the main control board. Ensure that all connections are secure and properly connected. Loose or faulty wiring can cause the light to stay on.
4. Test the main control board: As you suspect, a faulty main control board could also be the cause of the issue. You can try resetting the control board by turning off the power to the oven at the circuit breaker for a few minutes and then turning it back on. If the light still does not turn off, it may indicate a problem with the control board that requires replacement.

If you have performed these troubleshooting steps and the light still won't turn off, it would be advisable to contact GE customer support or a qualified technician for further assistance. They will be able to diagnose the problem more accurately and recommend the appropriate solution.

Could you please supply us with a Model# Kenada is a Ai Bot

ck here... https://www.justanswer.com/appliance/40xmk-ge-profile-range-oven-bake-probe-lights.html

Found this video.... https://circuitboardmedics.com/wb27t10282-oven-control-board-repair/#instructional-video Sure hope it helps shows your model # Best to you

Strange it won't turn back on. Did you see it working when you purchased it secondhand? It appears you just need to reset. Turn off at the breaker for 2 minutes, then back on and try this.

SOLVED: Our GE Profile JTP18 keeps flashing "door loc

Fixya https://www.fixya.com > support > t200245-our_ge_p... 6 answers If the oven is flashing "LOCKED DOOR" on the display. even though the door is open, the fix is easy and there is no need for repair. Press and hold the oven ... https://products.geappliances.com/appliance/gea-support-search-content?contentId=16196 lots more here https://www.google.com/search?q=GE+jtp15+wall+oven+locked+door+flashing%2C+4%3A00+flashing ..