Top 20
Kenwood KM300 Chef Stand Mixer Questions & Answers
Service advise for kenwood a700d
The planetary gear housing is filled with grease. Seeing oil come out would indicate that grease has started to or has completely broken down. Take the planetary apart (One nut and a clip), clean out the old grease and liberally repack with a food grade grease something like PTFE Super Lube .
Compatibility of mincer attachment
1) remove the front power outlet of the mixer head. 2) look for a notch in either the top edge or the bottom edge of the casting. (hole)3) Guide Pin on 9xx accessories is at the top of the connecting shaft. 4) if notch and pin point in the same direction, accessory will usually fit (9xx acc's point up and 7xx acc's point down)
Kenwood KM300. How to fit new mains cable ?
Having done it the hard way (!) it is dead easy. All you need is a small screwdriver or similar, approx 2mm by 1mm in cross section. Looking from outside the mixer, where the power lead enters the main body, between the rectangular lead casing and the socket it enters, there is a small rectangular cutout (top right). Push your screwdriver in around 15mm, and then withdraw the lead housing with it - the screwdriver pushes the latch aside, hence you need to remove both as one! With luck, and a wiggle or two, that should be it.
Oil dripping into bowel model km201
it just needs a new seal ..I had the same problem..it seems the seal will perish over time ...mine is back from repair and working perfectly
Kenwood_Wiring_Diagram kenwood chef A901
Hi Eward: This information is not always readilly available online. Suggest you contact Customer Support for Kenwood and inquire if they are able to make this information available.Go to the Customer Support site:
http://www.kenwoodworld.com/uk/Customer-Service/If necesary you the link to 'global site' to select your country and then scroll down and send an e-mail request to the contact name provided near the bottom of the page. Thank you for using FixYa!
How do i lower the attachments on a kenwood chef
First of all, thank you very much for choosing FIXYA today for your technical support needs.
Here is a direct link to the ONLINE USER'S MANUAL for that model:
http://www.kenwoodworld.com/Global/Instruction%20books%20(User%20manuals)/Food%20Mixers/88249iss5%20KM300,%20KM400,%20KM800%20English%20only.pdf
To view the Owner's Manual with Operating Instructions just use your mouse to click on the link, which is the underlined and blue highlighted text just above.
This will open a new web browser page automatically for you and allow you to view the information at the website indicated and the contents of the Owner's Manual.
You may need ADOBE READER installed on your computer to read PDF documents, although many computers already have this type of utility pre-installed.
You can download this free at
WWW.ADOBE.COM if necessary.
Click on the DOWNLOAD ADOBE READER button on right side of the ADOBE home page when you get there, then follow the onscreen instructions to install the software on your computer.
I truly hope that was helpful to you.
Good luck and take care.
Joe.
Hi , I have a Kenwood chef mixer KM 330 i bought a
HI.The thread to where tghe nut is attached might been loose.You can actually have it repaired by putting adhesive.Before you tight the screw put adhesive to the thread and tight the nut slowly.In this way the nut will be permanently engaged/fix and it will not easily loosen when the paddle moves.The other way is to replace the thread and nut as well.Thankyou for choosing FIXYA.
Can't remove steel bowl from
I am having this problem - I know it's a twist and twist off thing of course as I've used it many times. But now twisting it off is not working and I need to wash it!!! Can't believe this of all things has gone wrong, never mind anything electronic!
Cant releace the dough hook from my kenwood chef.
hi the lock nut on the shaft may have been loose allowing the shaft to screw into the dough hook you hve to unscrew the hook out of the shaft then unwind the nut down so you can release the shaft. other problems can occur if the retaining clip has unseated and jammed itself into the planet hub. this is more difficult and a kenwood agent would be consulted see
www.kenwood.co.uk for nearest agent.
Just stoppped working and we are having dinner for
WHEN A KENWOOD CHEF STOPS RUNNING THE FIRST THING TO TRY (PROVIDING IT HAS NOT
SMOKED FIRST) IS TO TURN THE TWO SCREWS CLOCKWISE THAT FIT ON CORNER OF MOTOR.
SMALL SCREWDRIVER THROUGH PLASTIC COVER WILL DO IT AS THESE ARE A FINE TUNER AND
CAN SOME TIMES VIBRATE LOOSE
I have a Rival-Chef Excel
I live in the US and have an old Kenwood KM230 Mixer that I absolutely love. Unfortunately I can not locate a replacement for the spashguard that has now cracked. The old splashguard item # 27215/31227 is the replacement spashguard....any solutions
Have a 20 plus year old Kenwood chef [navyblue and
for both attachments to fall out the planet hub must be worn out. check that there is a spring clip in the groove of the beaters. if you have had it repaired recently it may be running backwards which woluld eject the attachments.
Not finding what you are looking for?