Top 20 Kenwood KM305 Stand Mixer Questions & Answers

Take it back for an exchange. It is defective.

HI.When the stand mixer produces a popping sound during mixing this problem has something to do with the motor.Motor has bossing on it.This might not be lubricated well and eventually lossen up.That's why it produces a popping sound.And with regard to the burnt smell might be on the coil of the motor's rotor or armature.Is the unit still functioning eventhough you smeeell burnt wire?Thank you for choosing FIXYA..

Can't refer you to a dealer there but it is likely that only the motor's brushes need to be replaced. This isn't a difficult DIY job and the brushes shouldn't cost more than ~ $20 US.
You could also remove the housing covering the motor and see if the commutator is visible. This is a segmented copper cylinder and shouldn't be completely blackened although some signs of black is normal. The brushes ride on this cylinder and if the brushes have become too short, it can cause arcing and smoke. Clean that surface before installing new brushes and they too may smoke and cause rough running until they are worn in. The brushes can be had many places so you will have to choose one convenient to you:
Kenwood Chef Brushes

are there any sounds or noises when you turn it on

check out uk eBay

Manuals @ http://safemanuals.com/user-guide-instructions-owner-manual/KENWOOD/CHEF%20KM300-_E

Note that they share similar manuals.

For free recipes you can Visit http://www.bestrecipes.com.au/forums/showthread.php?t=3562

Good luck and thanks for usin Fixya.

Do remember to rate this solution.

home.shop.ebay.com.au/.../Appliances__W0QQBrand3d75b67ZKenwood3212b2e1QQ_
try this link

I had the same problem. Had to strip the machine down to get to the motor. On the top is a moving plate with various capacitors etc mounted. On the front side there was a Capacitor (At least I think it was) with the wire broken.
I resoldered it and the machine now works fine.

I hope this helps

Hi,

where are you from, i have phone number to agents that still provide support for A700 series.

Hi,

There are not any new parts from Kenwood to A700 series, try to find it on internet or if anyone in the forum has one.

Hi,

Contact a locale store that selling kenwwod and ask for a splashguard, the spare part number is KW604349 it´s a 'D' shape

I hope you didn't buy a new one, ours stopped last week after 25 years. All that was needed were new brushes for the motor. Anyone with a screwdriver could replace them. 4Kenwood had the parts to me in a couple of days.

If in the UK try espares; https://www.espares.co.uk/search/mo2748942/kenwood/blenders---mixers---juicers/km631-major-silver-+-at337 They may ship abroad ... I don't know, I am UK based.

Check the power supply: Ensure that the food processor is properly plugged into a functioning power outlet. Sometimes, a loose connection or a tripped circuit breaker can cause power issues.

Safety interlock system: The Kenwood Multipro 910 food processor usually has a safety interlock system that ensures all parts are properly assembled before it can start. Check if all the components, such as the bowl, lid, and blade, are correctly locked into place. If any of the parts are not properly assembled, the food processor may not work.

Motor overload protection: If you have been using the food processor for an extended period or with heavy ingredients, the motor may have overheated and triggered the overload protection mechanism. In this case, you will need to allow the motor to cool down for some time before it can restart.

Fuse or circuit breaker: Some food processors have a built-in fuse or circuit breaker that protects the motor from electrical surges. Check if your food processor has a fuse and ensure that it is intact. If it has a circuit breaker, reset it if necessary.

Mechanical issues: If none of the above steps resolve the problem, there might be a mechanical issue with the food processor. It could be a faulty motor, broken wiring, or a malfunctioning switch. In such cases, it is advisable to contact the Kenwood customer support or take the appliance to an authorized service center for repair.

Restoration https://www.google.com/search?q=Restoring+Kenwood+major+a707b Parts Diagram https://www.google.com/search?q=kenwood+major+a707b+parts+diagram Great information in the last link. You have to scroll a long way down the target page that is referenced here. https://hyperentang.wordpress.com/page/2/

Parts Distributors ' KENWOOD USA

https://www.kenwood.com > usa > Support > Parts_Dist... Replacement parts manuals and certain accessories not available from our Store may be ordered through the KENWOOD Authorized Parts Distributors listed below ... Missing: a707b ‎' Must include: a707b

A700 - Kenwood Chef Restore

https://www.kenwoodchefrestore.co.uk > Kenwood Che... A700 - Chef. Made in England - Kenwood, Woking, Surrey. ... Parts are obsolete. A -300 watt motor with centrifugal ... Download Instruction Manual - Here. Missing: a707b ‎' Must include: a707b

Kenwood chef A701A schematics - iFixit

https://www.ifixit.com > Answers > View > Kenwood+c... Sep 20, 2014 - Where can I find the schematics for a Kenwood chef model A701A in order to restore this machine?. Mike Jordan. Answer this question I have this ... 4 answers · 6 votes: I have probed my A701A and looked at one of the relevant patents. My provis ..

It sounds like there may be an issue with the motor in your Kenwood Chef Premier mixer. This could be caused by a variety of factors, such as a malfunctioning motor, a problem with the drive belt or gears, or an issue with the electrical components of the mixer. To troubleshoot the problem, you may want to try cleaning and lubricating the drive belt and gears, as well as checking the electrical connections and fuses.

Help in the link including from Kenwood themselves. It is likely to be the selector, the control board or the motor. Take it in for Dealer Service. https://www.google.com/search?q=Kenwood+kmix+doesn%27t+start ..

If you have a multi meter check the box caps and resistors for KM 2XX series then replace it whenever required. Some may differ in values like 0.15uF 275x2, 0.33uF 275X2 or 0.47uF 275X2 then resistors may also differ with different models but common to have 1.1k ohms 2watts. Also if caps are open it is good to check the 600V triac and replace it when giving out lower output. I also advise to clean the commutator esp when is is sparking a lot, you may use light sanding and clean it after. Check also if the tachometer is good, there is a resistor-like-coil hidden under a plastic tab with 2 wires. This gives feedback and via a magnet attached to the shaft. Check the motor brush if it is good or worn out. Lastly check all the switches because if one of them is not working properly you wont be able to let the motor run.

Take your pick :>D https://manualzz.com/doc/24514755/a901e-repair-instructions https://www.manualslib.com/manual/1239313/Kenwood-Hm-901.html https://www.google.com/search?q=Kenwood+a+901+repair+manual ..

I use white food safe grease. Here is an example; https://www.ebay.co.uk/itm/391996333570?epid=25018211366&hash=item5b44cd5e02:g:NlUAAOSwoeVdxAPv