Kenwood KM400 / KM410 Chef Classic Stand Mixer - Page 6 - Answered Questions & Fixed issues
How can I remove K beater from my Kenwood patissier which is jammed
Only a bit of CRC and some brute force is going to work. Unplug the machine. Remove the bowl, lock the head down, squirt some CRC around the top of the paddle where the shaft goes in. Get someone to hold the mixer from moving about then grip the paddle firmly with 2 hands and turn it left and right. Gradually you will begin to get increasing movement until in the end you will be able to unlock it from the shaft. Once it is off you will need to thoroughly clean the shaft then you will need to scrape out the inside of the hole in the paddle. I carefully use a small round file, I am trying to clean the hole out, not increase the size of it beyond what originally was. The hole size has become smaller over time because of flour or similar entering around the shaft during use.
3/2/2015 7:05:08 PM •
Kenwood Food...
•
Answered
on Mar 02, 2015
•
254 views
Kenwood chef keeps curdling eggs
Put water in Kenwood and a bowl inside the Kenwood to hold eggs. Eggs need to be done SLOWLY. Can also add a LITTLE water to aggs as they cook to slow down curdling . Basically you need to turn Kenwood into a double boiler. Lift bowl with eggs in and out of Kenwood to control temperature and whisk away now under control. Lift bowl and cool and slow down cooking and lower back in water and Kenwood to hear back up. Keep whisking and lift and lower bowl as needed. Some melted butter doesn't hurt either!
1/11/2015 10:51:21 AM •
Kenwood Food...
•
Answered
on Jan 11, 2015
•
162 views
REPAIR MANUAL FOR KENWOOD KM405
Same...do you mean that you want to replace the cord, or past that and inside the actual component? And both will require actually opening it up.
12/3/2014 6:14:30 AM •
Kenwood Food...
•
Answered
on Dec 03, 2014
•
187 views
What is the burning smell
Look in the oven, the cake may be burning. If the smell is from the mixer it could be a capacitor burning out, it could be a fault on the PCB, it could be a poor connection in the wiring, it could be a faulty armature, it could be faulty field windings, it could be a bush or bearing nipping up. If it's not amongst that list try getting back with more information.
9/27/2014 9:30:16 PM •
Kenwood Food...
•
Answered
on Sep 27, 2014
•
203 views
Kenwood major a9070
Required kenwood major A9070 service manual required. Please confirm whether it is available or not. thanks all.
3/9/2014 2:25:38 PM •
Kenwood Food...
•
Answered
on Mar 09, 2014
•
207 views
Broken wire - Kenwood A701A
black wire indicates negative so if you can see a place on the circuit board that looks like that's were it came from then get some advice from an electronics person before you put it together.
1/27/2014 1:17:22 PM •
Kenwood Food...
•
Answered
on Jan 27, 2014
•
95 views
How do you attach bowls to mixer
The bowl sits on a round plate. If the bowl cannot sit properly, moce the round base a notch on the right to give more bowl space.
11/29/2013 4:04:39 PM •
Kenwood Food...
•
Answered
on Nov 29, 2013
•
178 views
Catchpin
If by catchpin you mean the pin that locks down the head assembly then they are obsolete. Get it welded or braized up and carefully file it back to shape. If you only get it repaired where it is worn then you can follow the shape of the unworn part. When they are really bad sometimes the curved bracket it passes through needs welding as well.
11/24/2013 6:56:47 AM •
Kenwood Food...
•
Answered
on Nov 24, 2013
•
61 views
Overload motor
follow the book. You may otherwise overload and burn motor.
11/8/2013 2:18:16 AM •
Kenwood Food...
•
Answered
on Nov 08, 2013
•
92 views
Gearbox oil
I don't know how much gear oil nor what type of gear oil. But most likely anywhere you can get a-hold of gear oil... use what you can get. I would try restaurant supplies. In my city there is a place called Case & Drum that sells anything from the petroleum industry.
10/17/2013 1:48:41 PM •
Kenwood Food...
•
Answered
on Oct 17, 2013
•
190 views
Speed control swich on Kenwood Titanium mixer
The switch on the titanium has a flimsy week point and is always breaking. This is a stupid economy by Kenwood when there is now so much good competition. Mine broke after only 6 months and Kenwood were less than helpful suggesting I took back to where I bought it - 500 miles away!! I wish I had bought a Kitchen Aid
7/4/2013 2:34:48 PM •
Kenwood Food...
•
Answered
on Jul 04, 2013
•
553 views
Need to open gearbox
Hi, you need to put a large screwdriver into the front port, then undo the clutch dog
4/16/2013 8:26:55 AM •
Kenwood Food...
•
Answered
on Apr 16, 2013
•
713 views
When using my Kenwood Chef A901D the machine does
Late but I had the same problem and fixed it on me tod so maybe it will help someone else. There are two stages of closing, it will shut at around 6 o clock but it's locked when it's around 8 o clock (it should click into this same position when fully open) I fixed mine by pushing it down harder than I was doing. If it won't lock after this then a spring is borked.
2/27/2013 8:15:21 AM •
Kenwood Food...
•
Answered
on Feb 27, 2013
•
666 views
Not finding what you are looking for?