Top 20 Kenwood KM400 / KM410 Chef Classic Stand Mixer - Page 9 Questions & Answers

The machine needs stripping down as something it likely worn. The gearbox is also packed with grease and may need re-packing. They do need periodic servicing. Does it make the same noise with the bowl removed? Sometimes the noise will be attachments hitting the bowl. There is an adjustment screw underneath to see clearance. https://www.google.com/search?q=SMEG+Stand+Mixer+makes+loud+clanging+noise ..

There are several potential reasons why your KitchenAid dough mixer might be shutting off. Here are a few possible causes: Overheating: If the mixer has been running for an extended period of time, the motor may overheat and shut off as a safety precaution. In this case, you should allow the mixer to cool down for a while before using it again. Faulty wiring: If the mixer is shutting off when you turn it on or when you change the speed, there may be a problem with the wiring. You should check the wiring to see if there are any frayed or damaged wires that could be causing the issue. Clogged air vents: The mixer may shut off if the air vents are clogged, as this can cause the motor to overheat. You should check the air vents to make sure they are clean and unobstructed. Failed motor: If none of the above issues are present, the problem could be with the motor itself. A failed motor can cause the mixer to shut off, and it may need to be replaced. If you are not comfortable troubleshooting the mixer yourself, you should consider contacting KitchenAid customer service or a professional appliance repair service for assistance.

It is a mechanical gear driven speed controller, so the lever is not attached at the back. https://www.google.com/search?q=b20+mixer+speed+control ..

Question edited for full 'make model (what it is)'. There must be a spring in the base that helps the top rise when you depress the button. You will need to remove the base. The manual doesn't mention anything and there is no Service Manual https://www.manualslib.com/manual/1021018/Hamilton-Beach-63390.html?page=5#manual Very limited help here apart from JustAnswer dot com https://www.google.com/search?q=hamilton+beach+model+63390+mixer+tilt+button+not+working ..

Question edited for a lot more clarity. Time for a new one. Nearly all parts are obsolete. https://www.ebay.com/itm/266100009365?epid=66794889 Parts Suppliers. I checked 3 of them https://www.google.com/search?q=EHC650+parts ..

Tip it on its side and spray it with kitchen cleaner spray. Wait 5 minutes and try again. It is probably gummed up from a messy cake job. FULL 'make model (what it is)' in all questions please, first 3 words. ..

Hi, This sounds like it's a portion of the whole product. If you want that, you might need to arrange an order through nuwave or one of it's manufacturer partners that focuses on the plastic enclosure tha that you've mentioned. If that does not work, then you can reach out to a commercial kitchen product distributor to help with find the part. To find one, you can check on the back of your kitchen product boxes . They sometimes show a "distributed by" phrase in those areas. Thank you.

Unfortunately not available anywhere online. Check eBay once every couple of weeks. https://www.google.com/search?q=Cooks+sm248+manual ..

Question moved from Cars and Trucks. Stand Mixers don't normally have belts and I don't believe this one does as I can't find spare belts. They are operated by nylon cogs that run in grease. The most likely reason is the she shear pin has sheared. This is a small pin like a nail that goes through a cog or shaft and shears if too much load is put on the mixer beater or dough hook. It often happens if you make bread and have the speed too high. https://www.google.com/search?q=change+the+belt+in+a+Bodum+electric+mixer ..

Hi, apply some cooking oil to where the parts are connected. If that fails, please submerge the parts in a bucket of or tube of water and attempt to detach them from each other. If all else fails, please reference the manual to ensure that you've not missed a detachment procedure. Thank you.

The sparks are generally seen where the carbon brushes meet the copper commutator on the motor spindle. This is actually fairly normal. You can lessen it by spraying with some light machine oil, but eventually you will need to replace the carbon brushes.

Hi, The mixer looks to be an antique so you might start with Ebay to find that specific mixer part. Thank you.

Impossible to guess what make and model you have! Google make model replacement beater https://www.google.com/search?q=Moulinex+model+replacement+beater ..

Hi, If you call the glue manufacturers, they might be able to direct you to a substance that can dissolve the glue that was applied. Thank you.

Question edited for clarity, two question made into one. Duplicated post deleted. Refresh the page to see your question published. Turn the mixer upside down and spray WD40 into the beater holder holes. I think there is a ball bearing detent that hold the beaters and it is probably seized. Leave for a couple of hours and spray again for another couple of hours. https://www.google.com/search?q=Hamilton+Beach+025+HB+10+speed ..

Question edited for clarity. Unit has two maker badges. Any place that services Hobart Mixers will service yours https://www.google.com/search?q=hobart+mixer+service+london+england A.S. Catering seem to be the sales agent for them. https://www.google.com/search?q=22HI-B%20service ..

BIN IT AND BUY THE BEST YOU CAN AFFORD

Take a 4 foot length of string and put it through the loops of the stuck beater. Tie the end of the string in a knot. Put the loop of string under your foot and hold the body of the mixer and pull.