Top 20 eMachines E19T5W 19" Monitor - Page 5 Questions & Answers

This is usually a sign that the partition on your hard drive that the recovery media is located in is corrupt. 3 reasons for this:

1. bad recovery partition from the factory (bad image)
2. Virus or spyware corrupted files to prevent usage which would prevent you from removing the problem with a recovery.
3. Hard Drive issues (physical sections of the drive going bad.)

If you created recovery media, use those to recover your system. If you didn't, you may have to purchase recovery media from gateway for your model to recover the computer. While it may cost you $30 to $50 dollars for the recovery media, it is a lot cheaper than the alternative of getting a tech to try to repair the partition or track down the virus or spyware. The other advantage of recovery media is if the problems you were experiencing are hard drive related, you can put a replacement drive in and use those recovery disks to get your system working again.

it will look something like the above. this motherboard is often used in your model

dear you check the setting of your monitor.

It sounds like you are trying to do an upgrade to Windows 7, as normally the operating system comes pre-installed on the Hard Drive (HDD). If the hard drive is not recognised, then it is a hardware fault, take it back it where you bought it! If that is not possible, check that it is correctly fitted to the hard drive socket, otherwise it is back to a repairer.

Reload the OS and start over

Change the keyboard setup under the control panel.

The only time a motherboard manual is provided to the user if when the you:

• Build the machine yourself and purchase the motherboard outright
• Have a machine custom-built by a local computer shop.

PC manufacturers usually purchase customized versions of commercially available motherboards for the machines. They specify chipset parameters and BIOS contents specific to the build(s) they plan to create. Because of that, it is not usually possible to obtain a motherboard manual for such machines.

An E732z eMachine is a laptop computer. If a USB port is not working, it may be broken from the motherboard. Laptop motherboard repairs can be very challenging, often impossible if you don't have the right equipment or experience. You may be able to find dis-assembly information/instructions, however if the part itself is broken, you may have issues finding parts given eMachines less than adequate documentation for their computers in general. More often than not, a complete removal of the motherboard is necessary to work on it. You must observe static electricity precautions. You should have experience with surface mounted devices and know that permanently damaging a motherboard is very easily done without the right experience working on them. Replacement parts, including a complete motherboard can be found here eMachines Series E732Z Replacement Laptop Parts

There is no video output from your computer, that is why the monitor goes to sleep, check the cable and the video card.

Follow the instruction from the link below: https://support.google.com/chrome/answer/113910

Usually 3 or 4 beeps in a row on many systems is a RAM issue. If you have multiple RAM sticks try to remove one while the system if off and unplugged. Turn it on and see if the beeps continue. If so, remove the other ram stick and put back in the first stick you removed. Repeat the process for each stick of ram until the beeping stops. If it stops, this means you have found the bad ram module and can replace it. Some computers requires ram to be installed in pairs, and that the pairs match (Check the stickers on the ram to ensure both are the same type and speed) If the problem continues after removing and testing each stick of ram, you may want to have a service professional / Computer Repair shop take a look at the computer for further testing.

Which power button is flickering (your computer, or your monitor). Here's some tricks I would try... 1. Verify the monitor's power cord is plugged firmly into the wall outlet and the back of the monitor. 2. Verify the monitor cable is firmly connected to the computer and the monitor. 3. Verify that you have turned the monitor power switch on. 4. If the power light on the monitor is not on, test the wall outlet (plug in a light or something you know works). 5. If the power light on the monitor is not on, try a different power cord. 6. If the power light is on and yellow or orange or flashing, but nothing displays, or the display is incorrect, borrow a monitor from a friend. If that works, your monitor probably needs replaced. 7. Also, you could try your display on a friend's computer. If it doesn't work, your monitor probably needs replaced. If it works properly on your friends computer, the problem may be with your computers video output port, motherboard video chip (or video card, if you have one), or drivers. Good luck.

http://www.computerhope.com/issues/ch000235.htm read this please ......

Emachine el1300G 02w cmos jumper location eMachines Motherboards

Once black "highlighted" press enter.Options to enable or disable will appear.

Apparently, The motherboard for the t2984 is a SEABREEZE T3 according to the eMachines Parts Depot... http://hardforum.com/showthread.php?t=1089862

how to do this physically or just putting back a new OS there. or what to buy it. or what what parts are unclear.

• buy new,hdd, or 100x better SSD
• install it.
• install what ever OS you want. w7 -64bit new.

age 2011,

try not calling people who may help you idiots, you're not likely to get any meaningful help from strangers by being rude. And change from AOL. your kids are right. use gmail instead. If you really want password help regarding AOL email you need to contact the only people who can help - AOL. try 1-800-827-6364 for USA or 0844 499 5555 for UK

1. Password incorect- try to key in another one. 2. Caps Lock is ON or OFF. Try to remember is there any CAPITAL letters involved. 3. For God's sake stop spying on your fiance, and leave her(his) computer alone! :D

Check all connections. Here's some tricks I would try... 1. Verify the monitor's power cord is plugged firmly into the wall outlet and the back of the monitor. 2. Verify the monitor cable is firmly connected to the computer and the monitor. 3. Verify that you have turned the monitor power switch on. 4. If the power light on the monitor is not on, test the wall outlet (plug in a light or something you know works). 5. If the power light on the monitor is not on, try a different power cord. 6. If the power light is on and yellow or orange or flashing, but nothing displays, or the display is incorrect, borrow a monitor from a friend. If that works, your monitor probably needs replaced. 7. Also, you could try your display on a friend's computer. If it doesn't work, your monitor probably needs replaced. If it works properly on your friends computer, the problem may be with your computers video output port, motherboard video chip (or video card, if you have one), or drivers. Good luck.