Toshiba REGZA 32XV515DG 32 in. LCD HDTV - Answered Questions & Fixed issues

The main power supply regulator section circuit fault. Either it will be a separate board, or the part of main board. Check and replace damaged component/s at its main power regulator [SMPS] section circuit. Contact any service technician. If you wish to get some details; check the site linked here. Pull up older posts. http://electronicshelponline.blogspot.com/ It will be best to replace the power supply regulator board as card basis rather than making "Surgery" to it; which usually will make loss for both money and time. Even though you can make it right, it will cost around an amount equal to the cost of a new board; including the cost of (spare parts + service charge) More to say, most of the spare parts to it will be difficult to get from open electronic spare part market. This is true to most of the flat panel TV power supply boards; irrespective of its brand and screen size. Search the site by type in the "brand name" to your device; [Exclude the model number], in the "Search box at the top right of the display window of the Homepage" to get gathered related posts.

To buy a genuine one, contact the authorized service center for Toshiba.

solution
you can the set your wall by without stand.
the TV back side scruw adjust syetem.

Send report :[email protected]

Yes its fine to turn the power off at the power point. In fact this saves money because there is no idle appliance power drain. It is also a safe practice to disconnect the power at night or over longer periods of inactivity because there have been instances where plasmas in particular have caught on fire. Turning the power off will not affect your friends LCD TV they are designed and built by engineers who incorporate power surge protection. The circuit breaker should be one of very good quality and if this is the case then your friends LCD will be fine.

regza 32pb1e tv looks like there's a crack in the lcd.how to repair this and how much?

The main fuse and the MOV's (surge protection component) and a lot of circuits (main board, tuner module where the antenna is attached to).
This can be real bad, so you might as well open it to see if the fuse is blown and if it has any sign of burnt components.

If you are going to DIY and have proper tools, electronics knowledge, and know safety precaution then please read on: Basic troubleshooting guide here: http://www.fixya.com/support/r5093881-lcd_flat_panel_tv_troubleshooting_guide http://www.fixya.com/support/r6150077-basic_lcd_monitors_troubleshooting http://www.fixya.com/support/r7406380-tv_training_manuals Failed TV and Monitors pictures: http://s807.photobucket.com/albums/yy352/budm/ Learn about bad caps: http://en.wikipedia.org/wiki/Capacitor_plague Parts: www.shopjimmy.com Capacitors kit: http://lcdalternatives.auctivacommerce.com/Default.aspx he can make you a set of caps. Or www.digikey.com just make sure to use caps with low ESR, 105c, high ripple current, long life rating such as PANASONIC FM or FC series.

This is a common problem an a failry easy DIY fix.

Plasma and LCD TV sets are prone to having capacitors in the power supply section fail. This is the most likely cause for the probem you describe. When capacitors fail your will commonly see one or more of the following symptoms.

• No video, Power light is on or blinking.
• TV is making a clicking noise.
• TV takes a while to come on
• Screen is very dim or flickers.

Again, You can get a power supply repair kit with the parts, detailed instructions, and support from sites such as www.TvRepairKits.com . Or just click here to see more details on their kit.

Here are pictures of capacitors...Notice that the ones below look bloated. They have failed and will need to be repalced.



Capacitor being replaced! Fairly easy DIY fix.


Again, You can get a power supply repair kit with the parts, detailed instructions, and support from sites such as www.TvRepairKits.com . Or just click here to see more details on their kit.
.

A: "We recommend using LCD cleanser that can be purchased at any electronics store," says a customer service tech for Westinghouse, a manufacturer of popular LCD televisions. The cleaner can be found in both spray and wipe form. But what exactly goes into these LCD solutions?

Kai Hui of MG Chemicals, makers of one of many available LCD cleaners, explains, "The main ingredient in most wipes on the market is water. There needs to be a small percentage of isopropyl alcohol (IPA) to help get rid of the grease from busy fingers." Some LCD cleaning solutions may include up to 50 percent IPA, according to Hui, but any more than that could damage the screens.

Since I'd never suggest you spend more money than you have to, I'd start with a clean, soft cloth and regular ol' tap water. You can add just a capful of isopropyl alcohol to a glass of water if you need something to help loosen the greasy gunk on the screen, so it can wipe off more easily. Get the cloth damp and then apply to the screen instead of splashing the screen and trying to wipe up the liquid; and always -- always -- use a clean cloth, as tiny, hard particles trapped in the fibers can scratch the surface of your screen

If you were to log on to the manufacturer's web site, I think you will be pleasantly surprised as usually one is able to download, by model number, Customer Instruction Manuals, list of Dealers for spare part supplies as required.

Just Google the manufacturer's name and follow the links. Make certain you are directed to the manufacturer's web site as some search engines direct you to other sites and they charge for the information that is normally free of charge.

I hope this helps.

you will need a power board the laninat in the power transformer is vibrating causing your buzz wine

Make sure set on air,not cable in menu setting,Get a digital antena or a rooof antena.Hook up u should get the DTV free signal.

GO IN TOUCH WITH TOSHIBA AS THE SET WILL BE UNDER WARREN TIE ........SO FREE REPAIR AND SERVICE

Buy a flat panel bracket.Use a stud finder and bolt to the wall studs

hi

go to this site download ur tv manual and see what may be the problem hope it helps it might be kids lock or something to that effect then buttons on tv wont work until reset http://www.nodevice.com/

Hi, Please immediately stop using this device and send it to Toshiba for a repair or replacement. It's not normal for a tv to blow fuses like this and could be a fire hazard. Thank you.

I would try sing a TV converter and a digital converter and see if that fixes the problem.

Without a remote control, you can't. If you wish to buy its original remote control, contact the authorized service centre, or authorized dealer to your device brand. They can either give you a genuine remote control to your device, or can direct you, from where can you purchase a suitable one. To select a proper universal remote control, you should know about the number of digits to its set-up codes. There are 3 digit, 4 digit, 5 digit, 2 digit and even single digit codes, to some brand devices. After confirming this, check the sites linked here. All the sites have set-up code list and set-up procedure to many popular brand remote controls. Check which brand remote control has set-up code/s to your device brand, and buy that one according to availability. Brand name of the remote control isn't a matter, but it should have set-up codes in its code list, to the device brand you have. Please note: Every new universal remote control will have set-up code list, and set-up procedure along with its pack. Never accept a remote control, that hasn't both of this. For more details about the set-up codes, visit the site http://electrohelponline.blogspot.com/ Check these sites too. http://remotesearch.blogspot.com/ https://elektrotricks.blogspot.com/ Universal remote controls are available at most of the electronic spare part selling shops; as well as online shops. Visit the sites by Desktop computer and type in the brand name of your device in the search box at the right column. It will help you find the remote you have to buy. Mobille view has no search

Some people recommend trying to update the firmware via USB. Instructions here, http://hubpages.com/technology/How-to-Update-Toshiba-TV-Firmware. If it is a model 32C120U, there is a known manufacturers defect. This issue is cause by defective main board because the main processor is not well solder to the PCB or the e-prom memory lost the software data. Some time you can try replace the eprom memory on the main board (cost of the e-prom $15) or re-solder with a hot air gun the processor but 90% of the cases you have to change the main board, the cost is around $30 you can find it in www.myshoptvs.com these guy are super. To replace the main board is easy and takes not more than 25 minutes. This could be your board here, http://www.myshoptvs.com/marketplace/4169-toshiba-32c120u2-main-unit-461c4q51l11-431c4q51l11-vtv-l40613-m6662.html

These blinks [flashes] are fault indication (Error Codes). From the number of blinks occur at one time switch ON, you can get an idea about the faulty circuit section inside it. This will make repair easy. These are called blinking codes. Make sure about the exact number of blinking of the standby/power LED, by switching On & OFF the set, for at least two times. Count it carefully. If you wish to get some details, check the site linked here. It has details about blinking codes, and fault locating procedure, to many popular brand TVs and other devices. http://electronicshelponline.blogspot.com/ http://electro-medical.blogspot.com/ Blinking codes details of many popular brand TVs are given. Surf the site with patience. If blinks continue without any pause, the main board is faulty.