20 Most Recent Emerson LC320EM9 32 in. LCD HDTV - Page 4 Questions & Answers

Refer its user manual for details. http://electronicshelponline.blogspot.com/

my t.v. didn't have a blown fuse, so my fix may not work for you. mine would turn on and read "digital television" then go into "calibration" or "service" mode where the screen shows changing colors without ever showing a picture. by chatting online with the service department (something you may want to do), i found that by using the original remote for my t.v. i could easily hit two buttons on it to bring it out of that mode. i found one after searching extensively on amazon, bought it for $20 and this t.v. found in a dumpster has been working like new ever since. more serious problems with an emerson t.v. may not be worth putting money into as they're a low end brand of electronics.

Check and replace damaged component/s at its main board, or replace this board as card basis. If you wish to get some details; check the site linked here. Viewing it in "Mosaic" or "Magazine" will make surf easy. Surf the site with patience. Pull up older posts. Do a search by type in the brand name of your device at its search box. http://electronicshelponline.blogspot.com/

Check video cables

Have you checked your settings in the control panel? Also, does your tv have a source that is for pc?

If your LCD TV or monitor has stopped working, or is displaying one of the following symptoms, then it's a candidate for some new capacitors - Flickering screen - Screen image disappears after several seconds - Dim screen - Slow start - Power LED on, but no picture - Unusual colors and/or lines The primary cause of LCD TV and monitor failure is caused by faulty capacitors. You can examine the capacitors in your LCD TV or monitor and actually see if they are bad. If they appear bulged on top, then they need to be replaced. New capacitors will solve a host of problems in LCD monitors and TV's and will extend the life of your monitor or TV by several years. Take it to a repair shop

If you have something providing an optical signal, you will need something such as a receiver that will accept and decode the optical signal. If you are able to make use of the HDMI instead of the optical audio channel, this would be the easiest bet. Otherwise you are looking at needing to get a receiver if you want to have more than 10W of stereo output, or if you simply wish to convert the optical signal into something the TV can understand, any fiber optic to analog converter, such as Amazon item B003OND0N4 (Search that string on Amazon)

The main power regulator board [SMPE]]; is faulty, Replace it. If you wish to get some details; check the site linked here. Viewing it in "Mosaic" will make surf easy. Surf the site with patience. http://electronicshelponline.blogspot.com/ Pull up older posts there.

Please provide more details please. Gopakumar Gopalan Google

My AWA television did the same to me - I put in '6666' as the password, and that seems to have corrected the problem.

Direct Code Entry

1. Press and hold the SETUP button until the red indicator stays on, then release the SETUP button.
2. Press and release the desired Mode button (TV, VCR, etc.). The red indicator blinks, then stays lit.
3. Enter the 4 digit code from the code tables. Note: after a valid code entry, the red indicator turns off. For an invalid code, the red indicator flashes.
4. With your device on, press CHANNEL UP. If the device responds, no further programming is required. Note: If some buttons do not operate your device, try one of the other codes for your brand.

Codes for Emerson TV are: 0004 0009 0044 0135 0049 0051 0189 0053 0147 0039 0130 0227 0233 0250 0252 0254 0257 0265 0266 0310 0325 0456 0040 0041 0042 0021 0023 0024 0179 0045 0025 0027 0030 0032 0034 0035 0037

Try this link to download the user manual. It has all details. Emerson LCD HDTV Owner Manual ManualsOnline com

Cheap Capacitors in power supply section. Either solder or replace.

Check and replace its main digital processor board.

check screen settings like zoom