Contact your honeowner's insurance company and see if that damage is covered. I don't think any reputable company would advise 'reclaiming' parts of a cleaning device that sat in raw sewage.
I have a problem with the Samsung WA80U3 washing machine. The safety stop button is activated and I cannot cancel it even though I tried to press the water level + function for more than 5 seconds and there is no solution. Please help.
Question edited for clarity and add Maker.
Question moved to maker category.
It appears to be a known issue with these. I could put a couple of pints of CLR descaling solution in the bottom and leave it overnight. CLR is made for Calcium, Lime and RUST.
Samsunghttps://www.samsung.com > ... > Home Appliance
Aug 10, 2023 - This "black particles" will sometime disconnect themselves from the bowl during washing cycle and they will contaminate your just washed clothes ...
Missing: WA13F5S2 ' Show results with: WA13F5S2
If your Samsung Eco Bubble washer is filling with water till the top, it could be due to a faulty water inlet valve 1. You may need to replace the valve to get your appliance filling with water and working properly again .
However, if you suspect that the sensor is not working, you can try the following steps :
Check if the LED on the eco bubble wash button is on.
Check if there is too little laundry in the washing machine. In case of heavily soiled laundry, bubbles may not be generated very well.
Unplug the machine from the mains to ensure your safety.
Locate the two screws on the back of the machine that hold the top cover in place, and unscrew them.
Gently push the top cover back and remove it to expose the interior.
Take out the detergent container.
Identify and remove the screws that secure the front panel in place.
If none of these steps help, please contact a local Samsung service center
The most likely reason is that the components on the Control Panel are fried. This appears to be a UK or South African machine so voltage is 220 volts, and you were 100 volts over, twice what it was supposed to be. You may be able to make a claim on your electrical utilities company as they are supposed to give you a stable voltage. They may decline and say it was a lightning strike and an 'Act of God', but check weather records and counter claim.
https://www.ebay.ca/b/Samsung-Plastic-Main-Control-Boards-Parts/99697/bn_7117014204
Your washing machine could of had now died on you guys and is not working anymore.It would be cheaper just to buy a new washing machine than to repair the washing machine that is 10 years old now. The drain hose might be clogged or kinked or lid switch or the belt is not working in your washing machine.
This could be a Samsung WF45T6000AW washer. On this model (and most similar recent Samsung front-load washers), the dispenser drawer is to the left of the cycle selector dial. When you pull out the drawer, the compartment arrangement is: front left - liquid detergent, front right - liquid fabric softener. Liquid bleach goes into the back compartment. If you are using a powdered detergent, you have to remove the liquid detergent container. It just lifts out. Then put the powdered detergent in the front left- compartment.
I found the Use and Care manual on the product page, https://www.homedepot.com/p/Samsung-4-5-cu-ft-High-Efficiency-Front-Load-Washer-with-Self-Clean-in-White-WF45T6000AW/313846213 , at HomeDepot.com. The current link to this manual is https://images.thdstatic.com/catalog/pdfimages/1d/1d90b4de-ebaa-4d5f-a0cf-494bb1ffd212.pdf . The use of the detergent drawer is covered on pages 28-30. The description of the washer control panel starts on page 31. The cycle overview starts at page 35.
I hope this helps.
Cindy Wells
Yes, the Samsung washing machine model WA12VP has a drain pump. The drain pump is responsible for pumping water out of the washing machine during the draining stage of the wash cycle.
It is possible that the issue you are experiencing is related to the drain valve rather than the drain pump. The drain valve is what opens to allow the water to flow out of the machine, and if it is not opening properly, the water will not drain.
To troubleshoot the issue, you can try manually opening the drain valve to see if water flows out of the machine. If it does not, then the issue is likely with the drain valve and it may need to be replaced.
If the drain valve is working properly, then you may need to check the wiring and control board for issues that may be preventing the drain pump from activating during the draining stage.
