20 Most Recent Bosch 24 in. SGS66E02 Exxcel Built-in Dishwasher - Page 7 Questions & Answers

Hello. The control panel most likely wasn't the problem...the main control board probably was blown out causing the user interface to remain off. What was the unit doing or not doing that made you replace the control panel? BIG TIP--if you had a power interruption (such as lights dimming in the house--called a "brownout") or a full scale outage where the clocks reset, the main board very well could have been damaged by the current surge when the power came back on. *NORMALLY**, if the appliance wasn't damaged immediately, 4-6 weeks after the event, strange things will start happening or not happening with appliances because chips on the the board were damaged and start to fail. I tell all my customers to check into WHOLE HOUSE SURGE PROTECTORS--you can buy them at Lowe's or Home Depot and, your power company might install them on your house for a little extra on the bill each month--money well spent!

whats the model no?

please go here on pc, this tells you how to reset bosch dish washer. baubilt.com/?p=1318 This tells in full detail. God-Bless you all!

Code 24 means your drain is plugged or running slow

heater??????

Control

Hi, what's the model number? Thx

Hmmmmmmmm. If the water goes in and the pump starts yet there is no washing action I would suspect that you have an impeller failure. The impeller on Bosch dishwashers is a two piece unit and the plastic rivets slowly dissolve until he impeller fails in 2 pieces. The fix is a new impeller which is supplied with a new seal as well. I believe Bosch does this to avoid running so long without renewing the seal and having a leak. I can't think of any other reason to have a dishwasher soluble part for an impeller. It's a bit of a bit** to fix but there are good videos on utube.

Check water supply to dishwasher. If ok then check water inlet filter for block. If blocked clean or replace.

Bosch SMS Series Dishwasher Fault Codes E15 Water in base Float sensor in the base has been activated. You can try to empty the base and restart the dishwasher as you will find noted many times in the forums but, if there is a leak this error code will simply be displayed again, you must find the cause of the leak. but if you have a different model it can be something else

Sebaiknya diganti timernya itu biasanya sakelar tiketnya sudah rusak.

Check your drain hose, especially where it goes into your garbage disposal. Also, if you got a new garbage disposal, make sure the plug has been knocked out in the dishwasher drain port.

Try unplugging your dishwasher for 15 seconds or more, and then plug it back in. If that doesn't fix the problem, or if the problem comes back within a day, then you probably have a bad control board, or else the Auto key is stuck closed (like it is pressed).

There is often a filter inserted in the water feed pipe where it attaches to the machines valve and is part of the sealing washer, check that is also clear.

This is a computer error and really needs to be tested by an authorized repair company. There is one thing you might try and that is to unplug or cut the power to the unit for several minutes and see if it will reset.

https://www.bosch-home.com/za/service/get-support/manual-search Possible source of manuals from manufacturer web site.

It means that water is not getting to the dishwasher. Make sure your water valve is turned on all the way. If that's okay, then maybe your water supply hose got kinked when you pushed the dishwasher back in it's place. As a final check, turn off the water, disconnect the water supply hose at the dishwasher, and with the end of the hose sticking in a tall bucket, turn the water valve back on. You should have a good strong flow. If not, then your water valve (under the sink) is bad, and you will probably need to call a plumber, because the problem is not in your dishwasher.

Try the flow sensor which sits in the tank on the left handside

This is a common fault and apart from trying silicone sealant , it is beyond repair