20 Most Recent Bosch 24 in. SGS66E02 Exxcel Built-in Dishwasher - Page 2 Questions & Answers

It needs descaling. Try CLR in a wash

Add some salt.

Check if there is anything in the large item trap or blocking the water level sensor. The dishwasher won't try to fill if it believes it is full. Try pressing and holding the Start button for 3+ seconds. The Clean LED should light up in a minute. If it does, try the on/off button and starting a new cycle. (This just clears any old programs from the memory.) Some washers will stop if they detected a water leak. Sometimes turning off the power for a while and checking for water in the cabinet below the dishwasher or in the motor area is useful. The more likely items to check: Check the wiring between the inlet valve and the control board. Check the wires for corrosion at the connecting pins and for continuity. Broken conductors don't send a signal to open and close the valve. If those are okay, then the control board itself may be faulty. Since this dishwasher is discontinued by the manufacturer, I don't know if all of the parts are still available. The only parts list for the SHE3ARL2UC/28 that I found is here: https://www.partselect.com/Models/SHE3ARL2UC/ . They don't list any wires or the control board. I hope this helps. Cindy Wells

The water supply is inadequate for your dishwasher.

If you're seeing an E3 error on your Bosch built-in microwave, it usually indicates an issue with the touchpad or control board. Here are some steps you can take to try to fix the problem: 1. Unplug the microwave: The first step is to unplug the microwave from the electrical outlet for at least a minute. This will reset the control board and may clear the error code. 2. Check the touchpad: Sometimes, the E3 error can be caused by a stuck or malfunctioning touchpad. Check the touchpad for any damage or debris that may be interfering with its operation. Clean the touchpad with a soft, damp cloth and make sure it is completely dry before plugging the microwave back in. 3. Replace the touchpad: If the touchpad is damaged or not working properly, it may need to be replaced. Contact a Bosch authorized service center to order a replacement touchpad and have it installed by a qualified technician. 4. Replace the control board: If the touchpad is not the issue, the E3 error may be caused by a faulty control board. Again, contact a Bosch authorized service center to order a replacement control board and have it installed by a qualified technician. In any case, if these solutions do not work, it's best to contact a qualified technician to diagnose and repair the issue, as microwave repairs can be dangerous due to the high voltage involved.

https://www.reliableparts.ca/catalog/Touch-Up-Paints-467065 and Amazon of course!

Black Appliance Touch Up Paint

Amazon.com https://www.amazon.com > black-appliance-touch-up-... Rust-Oleum Paint 213174 .6-Ounce Specialty Brush Bottle Appliance Touch Up, Black, 0.6 Ounce. Enamel, Acrylic, Specialty. ..

I had this exact problem. There is a single hole on the underside of the arm, and it seems like the jet from it is enough to lift the arm so that it clears the plastic. The hole was clogged for me. Still have some thumping noise but it's 1/10th of what it was before.

The senors for your dishwasher are either dirty or need to be replaced.

I have a Bosch Silence Plus 46 dBA. SHS5AVF6UC/22. ...

JustAnswer https://www.justanswer.com > Appliance Repair Jul 5, 2021 - What have you tried so far? When I try to start the cycle, the red light on the floor comes on, it beeps, but won't start. 1 answer · Top answer: Hi and welcome to Justanswer. My name is ***** ***** to assist you today. I'm Why is my Bosch dishwasher beeping and not starting? Bosch dishwashers are designed to beep when there is an error. A beep means that your drain is not clogged, and the rest of the parts are functioning as they should. Beeping in the middle of the cycle points to the problem with the control board itself. Find the circuit breaker and turn it off for 60 seconds.

Bosch Dishwasher Error Codes ~ By I-Fix Appliance Repair

If the dishwasher is not starting the wash cycle after replacing the circulating pump, it is possible that there is an issue with the control board. You may want to check the wiring connections between the control board and the new pump to make sure they are properly connected. If the connections are correct, you may need to test the control board and its various circuits to see if there is an issue with any of the components. It is also possible that there is a problem with a sensor or switch that is preventing the dishwasher from starting the wash cycle. You may need to consult the dishwasher's user manual or contact Bosch customer support for further assistance.

You never mentioned anything about dirty dishes not getting clean. Run a load and let it go and tell us the results.

If you can see water flowing down the overflow channel to the pan at the bottom of your Bosch dishwasher while it is running, this indicates that there may be a problem with the dishwasher's float switch or water inlet valve. The float switch is a small device located at the bottom of the dishwasher's tub that is designed to detect the water level inside the dishwasher. If the water level rises too high, the float switch will shut off the water inlet valve to prevent the dishwasher from overflowing. If the float switch is not functioning properly, it may allow water to continue to flow into the dishwasher, resulting in water flowing down the overflow channel to the pan at the bottom. Another possible cause of this issue could be a faulty water inlet valve. The water inlet valve is responsible for regulating the flow of water into the dishwasher. If the valve is stuck open or is not functioning properly, it may allow water to continue to flow into the dishwasher, resulting in water flowing down the overflow channel to the pan at the bottom. To resolve this issue, you may need to have a professional technician inspect and repair your Bosch dishwasher. They can test the float switch and water inlet valve to determine the cause of the problem and replace any faulty components as needed.

You can find a replacement clic assembly for your Bosch 1587vs jigsaw online from Bosch or from third-party retailers. You can also find clic assemblies from hardware stores, home improvement stores, or tool supply stores in your local area. Make sure you get the correct clic assembly for your Bosch jigsaw model.

has a circulating pump with heater....

The noise my be do to vibration. Is there any spot on the dishwasher where you can put your hand to temporary stop the noise do to vibration? I’ll continue my answer after your feedback.

Here's some ideas....... https://readytodiy.com/bosch-dishwasher-not-completing-full-cycle-or-stops-mid-cycle-0051/

Try turning off the power are the breaker or wall plug for 5 minutes, which is a power reset. If that doesn't fix it, you will need a service call.