20 Most Recent Bosch 24 in. SHU43 Built-in Dishwasher - Page 5 Questions & Answers

0helpful
1answer

My bosch aqua stop dishwasher does not run all the

could be the microswitch on the door catch.
10/19/2013 10:14:57 AM • Bosch 24 in.... • Answered on Oct 19, 2013
0helpful
4answers

My bosch dishwasher will not dry the dishes

this dw to save energy works this way- the final rinse will reach a temp of 161 F . the dishes have to absorb this heat. when the cycle is complete the dishes become a heater in themselves radiating the heat they absorbed during the final 161 F heat. If you have any tupperware or plastic dishes in the unit they will not absorb heat therefore not radiate the 161 f temp need to dry all the dishes. try to avoid plastic items and they must always have jet dry. this is the european way of conserving energy. on the old ge or whirlpool they had electric element in the bottom that would bake the dishes dry ....not these..but they do save alot of energy.. it helps right after a cycle to crack the door open release all the steam from the unit
10/5/2013 10:59:59 PM • Bosch 24 in.... • Answered on Oct 05, 2013
0helpful
1answer

Continue to encounter a resistance burn at the

Check the resistance with a polymeter.Maybe you have problem wth the resistance.
9/14/2013 8:04:23 PM • Bosch 24 in.... • Answered on Sep 14, 2013
0helpful
1answer

MY BOSCH DISH WASHER STARTS RUNNING BEFORE WATER

Probaply you have problem with the door latch.See the following video.http://www.youtube.com/watch?v=gub9I5RFeiI
9/13/2013 9:20:08 PM • Bosch 24 in.... • Answered on Sep 13, 2013
0helpful
1answer

Intall drain pump

9/13/2013 9:18:07 PM • Bosch 24 in.... • Answered on Sep 13, 2013
0helpful
1answer

WHERE IS THE FLOAT SWITCH ON THE BOSCH DISH WASHER

Open the left door and you will see it.See the video belowhttp://www.youtube.com/watch?v=UwrYRrN0DQg
9/13/2013 9:16:00 PM • Bosch 24 in.... • Answered on Sep 13, 2013
0helpful
1answer

Bosch dishwasher stuck on zero wont finish cycle

Propably you have leak from the main pump impeller seal.This leak activate the floating probe that prevenge the end of the program.See the video below. It helped me to fix yesterday same problem.http://www.youtube.com/watch?v=DE7oYA5l3EQhttp://www.youtube.com/watch?v=RLkMncM6JDEIf you open the bottom of the dishwasher you can see the leak.It leaves calcium at the base of the pump.
9/13/2013 9:07:12 PM • Bosch 24 in.... • Answered on Sep 13, 2013
0helpful
1answer

I have a five years old kitchenaid dishwasher that

Propably you have leak from the main pump impeller seal.See the video below. It helped me to fix yesterday same problem.http://www.youtube.com/watch?v=RLkMncM6JDEIf you open the bottom of the dishwasher you can see the leak.It leaves calcium at the base of the pump.
9/13/2013 9:03:20 PM • Bosch 24 in.... • Answered on Sep 13, 2013
0helpful
4answers

Dishwasher will not fill with water

without a brand or model number its hard to be sure, but some types have a float cut out switch inside the washer. Its on the bottom inside and kind of resembles a plastic mushroom. The top should lift up and down easily. detergent will clog it up and keep it from moving. Just clean all the soap caked on it and move it up and down to see it it pushes a little switch underneath.
7/12/2013 8:47:20 AM • Bosch 24 in.... • Answered on Jul 12, 2013
0helpful
1answer

I have a BOSCH SHU43C

Hello,

Welcome to FixYa.


Based on your post it may just be a loose/burnt connection in the dishwasher junction box or a severed wire in the door panel.

** I would start by first shutting off the breaker...safety first**

Then removing the kick plate ( access panel at the bottom )...

macmarkus_133.jpg

...and checking the wiring at the junction box for the dishwasher 120vac supply line.

Remove the murret's and visually inspect the wire for "resistance burn" and strip the wires back and install new fastener's if necessary to repair.

i.e.

60f6a31.jpg

This is actually quite common to find a wire connector come loose due to improper fastening and once the unit is in use for a while the connections heat & cool, become loose from normal operating vibrations and burn up from all the added heat caused by "resistance".

Typically this will manifest in just the manner you've described.

If it looks OK there I'd remove the outer door panel ( careful the edges are sharp ) via the six #20 torx head screws...

macmarkus_168.jpg


...check for a severed wire at the pivot point in the door, typically covered in a plastic casing as shown here..
.

macmarkus_169.jpg

The small plastic blocks which may be present in the bottom corners of the door panel, i.e.

macmarkus_170.jpg
...they can be a pain to re-install, but they do only go in one way, however it is ok to leave them out...their only purpose is to strengthen the structure.



Ultimately it could be the main power switch is cooked, but I'd certainly check what I've suggested first and go forward from there. Good luck.

Let me know what you find and I'll try to assist you further if necessary. Thank you for choosing FixYa today for your inquiry.


Regards,

Macmarkus :)
6/22/2013 10:12:15 PM • Bosch 24 in.... • Answered on Jun 22, 2013
0answers
0helpful
1answer

Bosch LifeStyle Auto Keeps showing E-24 and will not proceed with wash

E24 Drain filters blocked

Clear the filters. Generic instructions to clean your dishwasher filter

God bless you

4/5/2013 6:31:05 PM • Bosch 24 in.... • Answered on Apr 05, 2013
Not finding what you are looking for?
Bosch 24 in. SHU43 Built-in Dishwasher Logo

1,005 questions posted

Ask a Question

Usually answered in minutes!

Top Bosch Dishwashers Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Mike Cairns
Mike Cairns

Level 3 Expert

3054 Answers

Cindy Wells

Level 3 Expert

6688 Answers

Are you a Bosch Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Bosch Dishwashers

  • Bosch Dishwashers

Most Popular Question

dishwasher smells

  • Dishwashers
Loading...