Bosch Classixx WFO 2866 Front Load Washer - Page 4 - Answered Questions & Fixed issues

Hi, please verify with the product documentation that the flashing-door symbol indicates what you've initially mentioned. Apart from that, you might look for the sensor and hold it in to temporarily overcome the issue. If the door being shut is the issue, pressing in the sensor should fix the issue for you temporarily. If not, then you can work with Bosch or Home Deport to moving forward. Prior to their arrival, you can power cycle your machine 1 or 2 times and check for the door symbol once more. It could be that they sensor has gone bad for some reason. Thank you

That sounds like a failed control board. You need dealer service.

Any of these. It is just water in, water out and two power wires. Look for one the same shape. You may be able to swap the mounting bracket over, or just drill new holes in the case. https://www.google.com/search?q=Hot+water+inlet+valve+00171295 Having said that, the part is here! https://www.repairclinic.com/ProductDetail/989550 https://www.google.com/search?q=Bosch+washer+wfk2401uc+water+inlet+valve ..

i think i would remove the outlet pipe take it to a yard water spicet and pressure blow it out to be sure it's clear then i would check where it connects on both ends to be sure those are clear then put it back together run it one cycle (empty) and see what happens.. it's also possible that the problem is from the screen in the water line going in.. being partially stopped up ... but i'm betting on the drain line.

Hope this helps there's a repair video..... https://www.appliancepartspros.com/bosch-belt-blower-154142-ap2805440.html

Hi, Please make sure that your laser-distance measure is charged properly to start. View it's screen for any listed error codes that could give us a clue to watch the issue is. If the error code hints at restarting the device, then we can move in that direction. If the error isn't revealed from perusing any troubleshooting documentation that comes with your device, then you can reach out to Bosch for repair/replacement help. Thank you.

Question edited for clarity, add words, make sentences and stuff. https://www.bosch-home.ca/en/service/get-support/error-e23-or-f23-washing-machine https://www.google.com/search?q=bosch+series+8+washing+machine+e23 ..

Disconnecting the power will normally release the latch.

Bosch washer error code f43 : Causes, How FIX Problem

https://all-errors.com > bosch-washing-machine-error-c... What does the F43 error mean in Bosch washing machine? It indicates that the motor does not rotate or something blocks the drum. What is the main sign, by which ...

Me too. What a piece of trash this washing machine is

Had a E90 fault,bosch condenser dryer found if I disconnected pump plug on the pcb mounted rear rhs of machine, rear connector with 2 red wires, fault would not be present and dryer would run, removed pump cleaned, and spun by hand, reassembled and operated correctly

Go to appliancepartspro.com enter your model numer and it will give you every part you need in diagram pictures.

Could be a blockage in the hose...remove the filter cover and give a hefty blow down the end of the drain hose (give it a wipe first). If there is an obstruction along the length of the hose this should expel it. If this does not help then you may have a blockage between the drum and the pump, when the filter is out, poke your finger in the small opening in the pump housing at approx nine o'clock and see if you can feel anything. Hope this helps, good luck.

Try this website. I explains the most common symbols Bosch use. https://www.bosch-home.co.uk/experience-bosch/using-your-appliance/washing-machine-symbols-guide#/Togglebox=8805164-8781535-1/

Check your door switch.

Hi Adrian. this is all i can find, Bosch Washing Machine E47 Error - Heat Sink on Motor PCB Fault

Description:

Heat sink on the motor control module is broken.

Action To Take:

1. Replace motor control module.
2. or go to this link it will give you all the codes.
3. https://appliancefault.com.au/faults/washing-machine-faults/bosch-washing-machine-fault-codes/

Use an external timer socket perhaps.

why you buy a second hand? For me, sometimes, it is only natural to have some errors in the second hand and why should you not check it before you claim or buy it? If I were you, I will return it to the owner and return my money... Don't buy any second hand especially in online shop because you don't know if it true or scam....

Turn the dial mode button to "sensitive" (wash mode) and then press the top left "menu" button for 5 seconds. That will deactivate the child safety lock.