Top 20 Bosch Classixx WFO 2866 Front Load Washer - Page 4 Questions & Answers

That sounds like a failed control board. You need dealer service.

Any of these. It is just water in, water out and two power wires. Look for one the same shape. You may be able to swap the mounting bracket over, or just drill new holes in the case. https://www.google.com/search?q=Hot+water+inlet+valve+00171295 Having said that, the part is here! https://www.repairclinic.com/ProductDetail/989550 https://www.google.com/search?q=Bosch+washer+wfk2401uc+water+inlet+valve ..

First you have to fix where the leak is coming from that tripped to E15 error code. You can reset by turning off power for 15 minutes. An E15 error code indicates that the safety switch has detected water in the base of the dishwasher. Your leakage protection system has activated. What can I do to fix the E15 Error Code on my dishwasher?

E15 Bosch Dishwasher Error Code

.https://www.google.com/search?q=dishwasher+e15+error ...

Hi Adrian. this is all i can find, Bosch Washing Machine E47 Error - Heat Sink on Motor PCB Fault

Description:

Heat sink on the motor control module is broken.

Action To Take:

1. Replace motor control module.
2. or go to this link it will give you all the codes.
3. https://appliancefault.com.au/faults/washing-machine-faults/bosch-washing-machine-fault-codes/

Error code E:21 on a Bosch Axxis front loader washer indicates a draining problem. Here are some steps you can take to troubleshoot the issue:

1. Check the drain hose for clogs or kinks. Straighten out any kinks and remove any clogs.
2. Check the drain pump for obstructions. The pump is located at the bottom of the machine. Clear any obstructions from the pump.
3. Check the filter for debris. The filter is located behind the front panel of the machine. Clean out any debris from the filter.
4. Check the drain pump for proper functioning. Test the pump by running a cycle with an empty drum. If the pump is not functioning properly, it may need to be replaced.

If these steps do not solve the issue, it may be necessary to contact a professional repair service for further assistance.

The suds sign on your Bosch Exxcel Vario 7 Speed Perfect washing machine indicates that there is too much foam in the wash. This can be caused by using too much detergent or using the wrong type of detergent. Here are some steps you can take to try to resolve the issue:

1. Reduce the amount of detergent: Check the detergent packaging for the recommended amount of detergent to use and reduce the amount if necessary. Overloading the machine with detergent can cause too much foam to be produced.
2. Use the right detergent: Make sure you are using a detergent that is designed for use in front-loading washing machines. Using the wrong type of detergent can cause excess foaming.
3. Run a rinse cycle: Run a rinse cycle without adding any detergent to help clear out any excess suds.
4. Check the detergent dispenser: Make sure the detergent dispenser is clean and free from any residue or build-up that could cause excess suds.

If the problem persists, it is possible that there is a problem with the pressure switch or the control module of the machine. In this case, it is recommended to contact a qualified technician to diagnose and repair the issue.

Try this website. I explains the most common symbols Bosch use. https://www.bosch-home.co.uk/experience-bosch/using-your-appliance/washing-machine-symbols-guide#/Togglebox=8805164-8781535-1/

Bosch do not list E61 as an error code. F16 means the door lock is faulty/misaligned.

Check your door switch.

Use an external timer socket perhaps.

Question edited for clarity and typo. Question moved to Bosch. If you manually drain by lowering to drain hose into a bucket, you should be able to release the door lock by turning off the mains power. You can also try a reset. https://www.google.com/search?q=Bosch+Series+2+front+loader+washing+machine+reset ..

I would try espares.com or Sears.com, depends on your country.

It's likely that you have a siphon occuring. Check the position of the drain hose. The bottom of the end of the hose must be above the maximum water level of the washer. In some cases, you may just need to pull the drain hose up and secure it so that it isn't pushed too far down. For other cases, you might need to lengthen the stand pipe by adding a coupler and another length of pipe. (If you have the drain hose going into a laundry sink, you might need to raise the sink if there is no easy way to get the hose secured in a higher position.) I hope this helps. Cindy Wells

The drain pump might either be clogged or broken or the bearings have now worn out and the tube seal could be ripped and also needs to be replaced for your washing machine and the drain pump needs to be replaced as well.

That error is for too long of a drain time. The machine may still have water in it. You need to drain it and then check the filter and the drain hose and pump. Since you did not post the model number of the machine, that is all I can tell you

Oh this is not good. Is there any portion of the wire that you can get a hold of with pliers? If not you can look on youtube for the videos about the machine disassembly.

It most likely needs a new water inlet valve. They are pretty easy to replace. https://www.google.com/search?q=bosch+wvf+2000+water+inlet+valve+replacement ..