20 Most Recent Bosch Classixx WFO 2866 Front Load Washer - Page 9 Questions & Answers

This error E32 is not such a problem.
It means that the system, responsible for protection against unevenly distributed laundry in the drum, has triggered. All you need to do is open the door, put large and small things evenly, and then additionally run a new spin cycle. Read the article: How to load things into the drum.

Bosch Washing... | Answered on Feb 13, 2019

Impellor in wash motor has broken , there is a kit which includes a new impellor and seals which can be used

Bosch Washing... | Answered on Feb 03, 2019

For Bosch washing machines, the E05 error indicates no water coming into the machine, the water being siphoned out of the machine as it enters or the water comes in too slowly. Do you hear the water coming into the washing machine? If you hear the water running in and draining out, check the height of the outflow tube. If it is below the water level in the washer, lift it up to stop the water being siphoned out.

If no water is entering the washer, make sure that the water supply shut-off valves are open. Next, check for kinks in the supply hoses. Turn off the shut-off valves and disconnect the supply hoses. Check if the filters are clogged on either the washing machine inlets or at the shut-off. Some supply hoses are designed to stop a flooding problem by restricting the flow if they are damaged. Try connecting the hoses to the shut-off valves. Then place a bucket under the hose, check the water flow rate by turning on the water to each hose individually. Alternatively, just replace the hoses.

If the inlet supply is fine but no water enters the machine, then the problem is probably with the washer's inlet valve opening and closing. You can test this with a multi-meter; most washers have a trouble-shooting sheet inside the machine (near the control board) which indicates the expected voltages and resistances. The valve will need to be replaced.

If water enters the washing machine without draining out, then the problem is with the sensor that determines the water level. Some machines use a pressure switch. In that case, the air tube can be clogged. That's often simple to blow out. Alternatively, the tube could be damaged. Sometimes the switch or sensor is faulty or the wiring could be damaged. In rare cases, the control board is not getting the correct signals.

Please add a comment with the model number of the washer, if you'd like me to search for a parts list or diagram. I hope this helps.

Cindy Wells

Bosch Washing... | Answered on Jan 27, 2019

Most often this is due to the door not shutting properly.

Carefully examine to see if clothing or lint or foreign body is interfering with the full closure of the door.

The washer will not start if it does not receive a signal that the door is full closed.

Bosch Washing... | Answered on Jan 22, 2019

Motor carbon brushes burned out and needs to be replaced. You can YouTube the procedure and do it yourself or call a service center and tell them you know precisely was wrong with it and how much to replace the parts and labor. It's a. 45-60 job
good luck

Bosch Washing... | Answered on Jan 17, 2019

Try cleaning the detergent draw somtimes this can cause water to spill out and ofcourse check the filter and exit pipe :)

Hope this helps

Bosch Washing... | Answered on Jan 11, 2019

Check drain pump for obstructions and operation

Bosch Washing... | Answered on Jan 01, 2019

Not finding what you are looking for?
Bosch Classixx WFO 2866 Front Load Washer Logo

72 questions posted

Ask a Question

Usually answered in minutes!

Top Bosch Washing Machines Experts


Level 3 Expert

85222 Answers


Level 3 Expert

411 Answers

Dw Wooten
Dw Wooten

Level 2 Expert

227 Answers

Are you a Bosch Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Bosch Washing Machines

  • Bosch Washing Machines

Most Popular Question

bosch classixx 6 1200 express error code

  • Washing Machines