20 Most Recent Bosch Exxcel WFO 2264 Front Load Washer - Page 8 Questions & Answers

Oh this is not good. Is there any portion of the wire that you can get a hold of with pliers? If not you can look on youtube for the videos about the machine disassembly.

the electronics lock out during power surges like you would get from brush failure giving e 21 error. you have to access service test prog to reset this, and it is not in public domain. i do know how to reset it though but difficult to explain on this forum you may find a you tube video if you search online.

Question edited for clarity and typo. Question moved to Bosch. If you manually drain by lowering to drain hose into a bucket, you should be able to release the door lock by turning off the mains power. You can also try a reset. https://www.google.com/search?q=Bosch+Series+2+front+loader+washing+machine+reset ..

look insides all racks removed to be sure things there do not belong there cups spoons, etc. make sure knives, in rack do not slip through the rack grid and hit the rotor below.

First you have to fix where the leak is coming from that tripped to E15 error code. You can reset by turning off power for 15 minutes. An E15 error code indicates that the safety switch has detected water in the base of the dishwasher. Your leakage protection system has activated. What can I do to fix the E15 Error Code on my dishwasher?

E15 Bosch Dishwasher Error Code

.https://www.google.com/search?q=dishwasher+e15+error ...

Yes, but also the wiring to the motor.

FROM FIXYA

Sanja Salatic NOV 29, 2009

The e2 error is a generic error that the machine shows if it's been overloaded or if the load becomes unbalanced during a wash cycle.

to fix you must do a master reset of the washing machine. 1. Close the door and make sure the dial is pointing to the "OFF" function 2. Hold the Start/Pause button and turn the dial anti clockwise (to the left) to the "express 15 min" program at the same time. 3. Hold the Start/Pause button for a minute (the e2 message is meant to start flashing after a minute of holding the button down however with my washing machine this didn't happen) 4. Release the button and turn the dial back to the "Off" function. 5. Select any program and the message should not be appearing. --------------------------

Turn knob to 12 o'clock position turn to 6 o'clock position press an hold the spin button turn knob to 7 o'clock while still pressing the spin button let go of the spin button after 5 seconds turn the knob back to 12 o'clock

That error is for too long of a drain time. The machine may still have water in it. You need to drain it and then check the filter and the drain hose and pump. Since you did not post the model number of the machine, that is all I can tell you

How about in French? http://www.supermanuals.com/downloadmanual.php?lang=en&iddocument=Dkyhbcsseg& So many manuals, but not yours. https://www.washermanual.com/bosch/ Should be here, but isn't https://www.google.com/search?q=bosch+WET+2820GB/13+manual ..

Gravel can't kill the motor. The motor is only connected via a drive belt. The only thing gravel can do is damage the pump as the gravel and water runs past the pump impeller! If it doesn't turn in wash (low speed), but it does spin in spin mode (high speed), my guess is the the belt needs tightening or replacing.

So basically it doesn't work at all. For a total failure like that it is likely to be the main control board, but because they are fairly expensive, you need proper diagnostics. Call for service.

Try doing a power reset. Disconnect power tonight before you go to bed. Some have a 'button press' reset procedure. Google Bosch (model) reset ..

https://all-errors.com/how-to-disassemble-the-bosch-washing-machine/

There are some videos in the link and if you click on the images tab there are schematics. The search query really needs the alpha numerical model designation though WRxxxxx. https://www.google.com/search?q=wiring+diagram,+bosch+classixx+series+4 ..

match old one at a hardware store

Likely a split hose, or a hose has come off. Pull the machine out and tilt it back against the wall. Have someone hold it whilst you check with a flashlight.

The blower motor is protected by the filters, so it shouldn't have an issue. The motor is hidden deep inside. Basically, you just undo every screw that you can find. Lay everything out in order and take pictures. https://www.google.com/search?q=Bosch+BGS4UGOLD2%2F11+vacuum+disassembly ..