20 Most Recent Bosch Axxis+ WFR 2460 Front Load Washer - Page 6 Questions & Answers


sounds like the thermal safety overload is cutting the power due to overheating hence why it just turns back on after a certain time, when the safety overload reaches a certain temperature it will cut the power to the machine or in some cases just the heating elements, once it cools down it resets and power is restored and by using the warm setting it obviously isn't as hot so its not overheating, its highly likely it is all blocked up internally with lint (i know it says self cleaning but they never work for more than a few years before requiring a proper clean and service)

Bosch Washing... | Answered on Dec 24, 2019


It means that the water is not draining fromthe machine inthe time allowed by the controller.

1. Switch off the machine and disconnect the mains power.
2. Remove the filter and make sure that the filter is not blocked and is clean and clear of all debris. Clean as required. Note that depending on the machine type you may get a lot of water coming out of the filter when you remove it if the machine has not drained successfully. Note that if the machine has stopped and not fully drained then you may be able to drain out the excess water by removing or disconnecting the waste hose and laying it on the ground in a tray.
3. Proceed by checking the drain hose for proper connection and kinks and make sure that it is not blocked.
4. Also check that the main waste drain pipe, if you use one, is not blocked and clean if required.
5. Reconnect the power and switch the machine on.
If the problem persists then do the following.
6. Switch off the machine and disconnect the mains power.
7. Check the electrical connections at the pump and make sure it is operational.
8. Remove the connecting hoses, and expect water to drain out and make sure the pipes are not blocked with debris or any object blockage.
9. Makes sure the pump appears clear and that the impeller looks in good condition.
10. Reconnect the hoses and then reconnect power and switch the machine on.
11. If problem has not been corrected, then remove the pump and check that the drive coupling to the motor is OK and that the motor turns OK. If all is well then replace the pump.

Bosch Washing... | Answered on Dec 21, 2019


E 06 means slow or no drain//not a easy do it yourselfer machine//you will need to get to the pump might be plugged//for the do it yourself you can get to the back( but this won't be easy) most techs if they know the machine will take front of that takes pratice//anyhow take rear panal of you will see drain pump in there remove tub to pump hose most likely has some items inside//note some bosch washers have small pump drain hose to get water out before you remove pump hose/if it will drain do that first save alot of mess...........(((( check this first))) note some have round cover at lower bottom put pointy item in hole of cover turn to release ( it will turn hard) some also had cleanout behind that cover/ if so check pump from that location much easier then taking back of.....Hope this helped if it did please vote...if you need more help please ask ...good luck

Bosch Washing... | Answered on Nov 25, 2019


Hi , could any know what F67 ERORR CODE FOR . IT KEEP SHOWING ON THE SCRREN MY WASHING MACHINE IS I XX8 BOSCH
Thanks

Bosch Washing... | Answered on Nov 08, 2019


If your model is WFMC3301UC/06, the Main Control Board is: OEM Part # 00660809

Bosch Washing... | Answered on Nov 07, 2019


FROM FIXYA

Sanja Salatic NOV 29, 2009

The e2 error is a generic error that the machine shows if it's been overloaded or if the load becomes unbalanced during a wash cycle.


to fix you must do a master reset of the washing machine.

1. Close the door and make sure the dial is pointing to the "OFF" function
2. Hold the Start/Pause button and turn the dial anti clockwise (to the left) to the "express 15 min" program at the same time.
3. Hold the Start/Pause button for a minute (the e2 message is meant to start flashing after a minute of holding the button down however with my washing machine this didn't happen)
4. Release the button and turn the dial back to the "Off" function.
5. Select any program and the message should not be appearing.
--------------------------

Bosch Washing... | Answered on Nov 03, 2019


CL indicates child lock has been activated. to deactivate it you need to press and holding the start button for 5 seconds.

Bosch Washing... | Answered on Oct 30, 2019


the electronics lock out during power surges like you would get from brush failure giving e 21 error. you have to access service test prog to reset this, and it is not in public domain.
i do know how to reset it though but difficult to explain on this forum you may find a you tube video if you search online.

Bosch Washing... | Answered on Oct 17, 2019


Hi, I know it's kind of a silly thing but when loading the machine make sure nothing is jammed against the dispenser preventing it from opening. I've run into that a few times and people looked at me like I had two heads but when I showed up to look at the machine,it was loaded like thanksgiving dinner was just over. If that is not the issue then it's either the dispenser itself that is broken or it's not getting power from the board. Either problem will require getting into the door of the machine and running a test program. I would call a local appliance repair company as these tests require the machine to be powered up and specific tools. Hope that helps.

Bosch Washing... | Answered on Oct 17, 2019


Vanessa Lopez Oct 12, 2019
I have a Bosch 300 Series on a pedestal. Pull the drawer out completely and reach to the back of the slides, you will feel the plastic release. The left one presses up (pull the drawer a little While you press the tab up), the right one presses down (pull the drawer a little while you press that tab down). Now you can simply pull the drawer all the way out.

Bosch Washing... | Answered on Oct 12, 2019

Not finding what you are looking for?
Bosch Axxis+ WFR 2460 Front Load Washer Logo

125 questions posted

Ask a Question

Usually answered in minutes!

Top Bosch Washing Machines Experts

Marvin
Marvin

Level 3 Expert

85223 Answers

jimorris77

Level 3 Expert

411 Answers

Dw Wooten
Dw Wooten

Level 2 Expert

227 Answers

Are you a Bosch Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Bosch Washing Machines

  • Bosch Washing Machines

Most Popular Question

pump blocked cannot open remove cap

  • Washing Machines
Loading...